All Installation Instructions for Hotpoint Dishwasher HDA1100N10WH

Damaged rinse agent dispenser

Unscrewed old one and installed the new one.

Parts Used:

Rinse Aid Fill Cap

Ralph from McMinnville, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

7 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Severe lwater leak around door

Removed door panel. Removed old door seal and cleaned seal recess. Installed new seal. Replaced door panel on door and ran a cycle to check for leaks. Readjusted door latch to correct small leak. Ran another leak test. Job complete and wife is happy!

Parts Used:

Door Gasket - White

Merle from Boulder, CO
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken off end caps, top would slide off, frustrating.

did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.

Parts Used:

RACK SLIDE END CAP

Paul from Blairs, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rinse Aid Fill Cap melted because it landed next to the heating element because it wasn't screwed in

Simply screwed in new cap

Parts Used:

Rinse Aid Fill Cap

Helen from Carol Stream, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

lower rack was rusty

Took out the old one and put in the new one! Note the delivery time was great! The part was ordered one day and delivered the next! Thank You Ed Andrews

Parts Used:

LOWER RACK

edward from noblesville, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

2 wheels on original track rusted/broke through

Removing the slide end caps was a little tricky. Key was to tilt and twist the end cap and slide out. Putting them back in was equally as tricky, but reversing the process helped. Sliding the new track in place was simple. Total repair took about 6 or 7 minutes.. Part was ordered on a Monday morning and delivered the following day using standard shipping. Outstanding service.

Parts Used:

RACK SLIDE END CAP

UPPER RACK

Allan from Williston, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

new bottom dishwasher rack

it was super easy and the part came in days. it was super quick

Parts Used:

LOWER RACK

Jose from Anthem, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dishwasher leaked

Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.

Parts Used:

Door Gasket - White

Robert from Colleyville, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

leaking water

The replacement of door rubber seal was easy as well as the corner boot tub baffles. I did take the door off to make cleaning and installing seal easy. I wish your web site would recommend if replacing certain parts, additional
parts should be replaced at the same time. For my project I should have
replaced the 3 inch separate seal located inside bottom of door. You can't
see it until removal of the door. I am thankful for the easy to follow
instructions other people wrote and it made the job much less stressful..

Thanks again

Parts Used:

Door Gasket - White

Corner Tub Baffle - Lower Left

Corner Tub Baffle - Lower Right

Scott from danville, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The problem was that the dishwasher lower sliding shelve was rusting out and coroding

We ordered a new lower shelve and slid it in on the rollers and it is secure and works fine.

Parts Used:

LOWER RACK

Carolyn from Novato, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

NONE

UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS

Parts Used:

Lower Rack Wheel Kit - 8 Pack

Edward from GRAND BLANC, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken spring on door.

See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.

Parts Used:

Hinge Arm Link

Ron from SOUTHPORT, NC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

One axle cracked and broke off; another wheel was had fallen off and was distorted when it hit the heating element.

Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.

Parts Used:

Lower Rack Wheel Kit - 8 Pack