Models > GTWN2800D1WW > Instructions

GTWN2800D1WW General Electric Washer - Instructions

All Instructions for the GTWN2800D1WW
301 - 315 of 342
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken belt
The belt is very tight. Use a zip tie to old the belt on as you work it around the large pulley. Once it is on remove zip tie and turn the pulley enough times to line up the belt evenly then your done.
Parts Used:
6-Rib Drive Belt
  • Thomas from Hopatcong, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Selector knob would spin and not grab selector dial.
Just pull up on the knob and remove the clip with needle nose pliars. Remove the knob, remove the dial and now install the new dial, the new knob and the replacement clip. The new knob comes with a new clip as well.
Parts Used:
Dial with Compression Ring Timer Knob
  • Rudy from San Leandro, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
The timer knob no longer engaged and moved the stem
I used needle-nose pliers to pry out the little c-clamp that held on the timer knob, then easily pulled off the knob. I used the vacuum cleaner to clear the broken plastic teeth from area surrounding the stem. Then I simply pushed on the new knob. Whole job took about 5 minutes.
Parts Used:
Timer Knob
  • Bryan from Poland, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Dial teeth were gone from the compression ring.
Remove the clip holding the knob and removed the knob. Removed the compression ring and replaced with a new ring. I used the instructions in the video that came with the verification of the order.
Parts Used:
Dial with Compression Ring Timer Knob
  • Patrick from Kiln, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
selector knob was worn out ordered a new one
recieved part in 3 days put knob in and was ready to go, good as new thanks
Parts Used:
Timer Knob
  • ANGIE from BARSTOW, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Knob on washing machine had broken teeth and would not turn the timer.
Used needle nosed pliers to pull plastic clip off the back of the old knob. Pulled broken knob off. Put on new knob over the metal post. Put on the plastic clip back on the back of the knob to hold it in place.
Parts Used:
Dial with Compression Ring Timer Knob
  • Brian from Bloomington, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
One of the paddles broke from washing something that wedge in between one of the paddles and side of tub. Which broke the blade. Order the the part from Parts Select. Watched the Video how to change the Agitator. It was as easy as they said. Repaired it myself for least than $50.00.
Pull the Agitator out by hand no tools where needed. Took Fabric Softer dispenser off put it on new Agitator. Pushed the new Agitator on. Repair done. Sure am happy I did it myself. Service charge from repair company would have been a lot more then $50.00.
Parts Used:
Dual Action Agitator
  • Pamela from Locust Grove, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
knob not turning/cracked inside
Pulled bad knob off. Found clip from bad knob still on and removed. Slid and aligned new knob on.
Parts Used:
Control Knob and Clip - White
  • Daniel from Glen Mills, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
timer and control knob
This repair is super easy. Take out the 6 phillips screws on the back of the control panel. Disconnect the timer wires and plug into the new timer--One wire at a time to make sure they fit into the same slots. Reinstall the timer and knob and back of the dryer and you are done. No need for a technican here. Save some $.
Parts Used:
Control Knob and Clip - White
  • Bob from MOUNT AIRY, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Timer knob was stripped and would not advance the cycle either manually or automatically.
Pull the knob out on the machine, remove the plastic clip from behind the knob and take the knob off. Install the new clip halfway onto the new knob, put the new knob in place and set the clip all the way in. 5 minutes.
Parts Used:
Timer Knob
  • maryellen from troy, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Would Not Spin Would Not Drain
Easy I followed the video. It took approx. 15 Min. Thanks to the video I feel like I can repair anything. This is not the first appliance I fixed. Thanks to parts select.
Parts Used:
Lid Switch with Wire Harness
  • William from Urbana, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
No hot water fill
Installation went okay but still only get cold water fill
Parts Used:
Temperature Switch - 3 Position
  • Joanne from Millican, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
The timer knob was stripped.
I watched the video and did the same thing that was shown. It was a very easy process!
Parts Used:
Dial with Compression Ring Timer Knob
  • Steven from North Arlington, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Start Button Fell Off
Turned off all power. . . Took top back off. . . Retored starter back in position. . . Attached knob. . . Replaced back, turned on power. . . And thanks to utbe instructions
Parts Used:
Control Knob and Clip - White
  • PHYLLIS from north lauderdale, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The timer knob was broke
Watched the video you had on how to replace it and did it like you showed and said and it worked fine.
Parts Used:
Timer Knob
  • Thurman from Marshall, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GTWN2800D1WW
301 - 315 of 342
Back to Top