Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Uppper Dish Rack with wheels
It was tricky to get the old rack off. Usually you can unclip the clips closest to the front wheels to pull the rack out. However, there is an area behind one of the wheels that you can kind of release and than pull the rack out. You then have to slide out the funnel/fan piece from the middle. That piece slides/ snaps in the middle of the the new rack. Then slide the new rack in place, re attach the release used to slide oldrack out. That is it !!
Replaced the upper dishwasher rack due to rusting.
To remove the upper rack, twist the support rail end caps toward the center of the machine and slightly downward. The caps will come off and you can slide the new rack into place. Reverse the process to replace the end caps. One of mine broke and I will need to order replacements. The original rack is no longer available. The replacement, which is the only one GE offers, has less storage space and is not as sturdy. It bends downward when full. I am very disappointed and recommend not replacing the rack unless you have no other choice.
At first I found some water on my hardwood floor by the dishwasher, I thought that I might spilled't the day before, then it hapened again, so I remover the front lower cover for the dishwasher and I found water under the dishwasher, then I turned on the machine and I found a pin hall water leak from the water inlet valve. I turned the machine off, then I closed the water valve under the sink, then I disconected the power plug from the valve, the diconected the water supply copper pipe, then diconected the house from the valve to dishwasher, then got the part# from the valve sticker and the model# for the dishwasher from inside of the door. after that I went online and I got the valve. make sure to try more than one website because they all have differant prices, and Parts Select was the lowest one.
Dishwasher would not run with the door completely latched.
I removed the scews holding the inside door to the outside door section. Once removed I removed the 2 screws that held the switch to the door. After removing this switch I had to open it up to expose the four wires on the switch. I reattached the four wires to the new switch closed it up and placed it on the door with the 2 screws. Replaced the inside door. Job finished with the switch working and the dishwasher operating as per the factory standards. Very easy job and by doing it myself I saved money on a service call.
Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff
I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.
Ordered rubber connector and it arrived the next day. Shut off main power and water. Disconnected water supply and pulled unit out from under counter. Flipped unit over on it's side. Disconnected wiring, drain hose, clamps and completely removed motor/pump. Rubber connector would not unscrew by hand so I found a drinking glass slightly smaller in diameter than the connector inner diameter. Inserted glass in connector and proceeded to unscrew connector by turning connector and glass together. After removing old connector I cleaned the mating part after removing it from inside the washer and removed all the build-up. Replaced everything back in same order.
The plastic hose chamber was damaged and leaked when dishwasher was in use.
First I removed the four screws that secure the dishwasher to the underside of the countertop. Then I removed the four screws from the front cover at the toespace. Next I used an adjustable wrench to turn the feet to lower the unit enough to slide it out of the compartment. I unplugged the dishwasher and turned it on its side in order to access the hose chamber. I used a pliers to loosen the clamps at each end of the hose chamber and removed the the damaged item. Next I slid the ends of the new part into place and used the pliers to reposition the clamps. Finally I returned the dishwasher to an upright position, slid it back into the compartment, adjusted the feet to raise it to the proper height, put the toespace cover back on, secured the top of the unit to the underside of the countertop and I was good to go. No more water leakage.
Removed 4 screws, took off basket covering, put new part in one turn, then replaced covering. Plumber had come out, I watched what he did, he had to order part and come back. I asked how much he didn't know but said cheaper than buying a new dishwasher. When he left I started calling around about the little plastic part that I needed. Part was $15.50. They called and said it would be $110.00. Needless to say I called them out and ordered the part myself and put it in. Took me like 6 minutes and cost $21.69. I was so mad about this situation that I even got my service call money back that I had already paid.
I used the website to identify a few different problem areas. I found that the motor shaft would not turn. Upon removing it, it did turn, which lead me to look at the Impeller which was worn / frozen. Ordered new impeller and installed 100 % success !!!