AFI2538AEW00 Whirlpool Refrigerator - Instructions

Very simple--Just remove all drawers, remove old end cap, remove slider from old end cap and put on new one. Screw on new end cap and replace drawers. Took about 10 minutes.

I just exchanged it, was really easy. Ordering of your well set up internet page was very easy and the part arrived extremely fast price was very competitive. I am very happy with the service provided.

First, I took out the glass tray along with the two slide out compartments that are part of that assembly. Then I used a small socket set to take out the three screws that hold the part in place and along with the part a plastic connector comes out with it that adjusts the temp of the bin area. Line up the holes on the slider and two screws come out that hold the slider to the part. Disconnet the plastic piece in the back that adjusts are flow (press down plastic holders) Reattach the slider, snap the plastic piece on the back and reassemble. Sounds complicated but once you are in there, its self explanatory.

Parts delivered quick. 15-20 minute repair time. Just needed to remove a few shelves, then screws to remove damaged parts and replace with new. Very easy repair.

one screw and electric plug and the unit slide out. Slide the new one in and your ready to go.

It was quit simple. I removed the draw and the shelves above the pantry unit. Once everything was removed (2min), I removed the one side pantry bracket ( 2 screw's). Put in the new pantry bracket and screw's and I was done. I'll give it ten minutes total. easy button Thank you

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Took off the old gasket and pushed in the new one.
Note on the left door, you will need to remove the center piece. suggest watching youtube video.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Removed the door and replaced the broken door closure bushing. I had courteous help and responce from Parts Select people. Excelent turn around time on parts delivery.

I broke the glass in the frig and found partselect and ordered the new glass and had it in 2 days. Very fast shipping.

A jar was dropped on the chef's pantry lid and cracked the lid. I unhinged one side of the lid from the pantry drawer by gently pushing outward on one of the hinge pins. The lid slid out easily. I then reversed the process using the new lid and it went in smoothly. Be sure to align the lid so it rests on the shoulder of the pantry drawer. Simple task, no tools, and less than 5 minutes effort. The replacement part was perfect.

First it was critical to have gone on-line to see that many other people have had the EXACT problem with their Maytag refrig. It went crazy at 830pm the Wed before Thanksgiving! There would have been NO WAY that we could have had that repaired with the holiday! I went to Parts Select and ordered the part that very night ( they were open and taking customer service calls until 11p EST). They had the part to us first thing Monday morning!

The installation was simple and they provided perfect instructions as to the programming of the code.

I cant believe that Maytag has not dome some sort of recall on the control board for these refrigerators. When we looked at the old one, there was moisture on the plastic panel and the 2 capacitors were corroded and bulging. We are going to try and get those replaced, so we have a spare board.

It was a whole lot cheaper to replace the board, and many would just resort to paying a repair bill of >$500.00 for the cost of a $200.00 part and about 15 minutes. You dont have to be an electronics major to fix this either!

This whole thing saved us well over $2500.00, as we are not buying a new refrigerator. I will say that we will never buy another Maytag at this point! All beware and might want to have an extra control board handy!

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

proped up frig, loosened screws, cut pin, installed rooler w/ new pin, rounded pin end, reistalled, lowered frig...everyone happy, thanks again partselect.