ADE20L1H Admiral Dryer - Instructions

Took off top and front. Removed belt and pulled drum straight out. Unclipped the rollers. And noticed the rod that holds the roller was worn out badly. Good thing I bought the kit. Because it came with everything needed and was cheaper then buying the rollers seperate. Only hard part was putting the new mounting on for the rod. They are not predrilled. So does take some force. Put everything back togetther and dryer is working like new. fyi you can also clean out your air duct of lint buildup when doing this project. Had a repair man come over 2x in past year and each time he would replace the roller and charge me $150 each time. I spent $300 on that bozo. When i could have ordered the parts myself for a fraction of the cost. This was well worth and easy to do.

removed screws on back plare and replaced heater element. Thank you very much foe your quick delivery of the part I ordered. I was reall;y schocked to see how fast the part arrived. I will recommend your site to anyone who needs parts like I did,.
Thany you Very Much,
Alan Brooks

Lifted hood ,and took two screws and tilted the front back and remove the door switch , and took front off ,use little socket set, took cover off fan housing took pliers removed clamp on fan , remove key way on end ,slid fan off and put new one on and reverse the way if came off.

I suspected (correctly) that the thermostat was malfunctioning so I ordered the Heating Element Kit. This repair would have taken less than 15 minutes if I would not have dropped one of the sheet metals screws in the back of the dryer when re-installing the heating element.

removed front cover, lifted drum up with a clamp and replaced slides. Replaced front cover

Item # PS11740721 motor drive pulley. This has a 3/8-24 reverse thread inner bore. Fit my Maytag model MDE508DAYW dryer made by Whirlpool, with drive motor on the lower right below the counterclockwise rotating drum and exhaust blower at the front of the machine. It might work with a number of brands of dryers made by Whirlpool with that configuration. Check the motor shaft thread and the drive belt which is a 5 rib belt 5/16ths inch or 8 mm wide. For Joe Blow the local appliance repair places only quote replacing the motor and pulley as a unit. At $170.

I just used screw driver to pop of clip put new roller on poped clip back on

Had to disassemble most of the dryer including pulling dryer drum in order to get to drum support rollers. Not a real difficult repair, just time consumming because of amount of parts needing to be removed inorder to get to rollers.

Very simple-remove 3 screws that hold the Control Panel on, remove the two connectors and replace with new part in reverse order. Unfortunately, this did not fix the problem. Will be ordering complete timer assembly.

googled"dryer not heating". landed on partsselect.com. checked parts like website said with multimeter. pointed to thermostat. ordered it, replaced it, it works now.

First I removed the screws of the dryer cover. Next removed the screws holding the dryer drum.

Drilled out the two rivets left from the old glide. Inserted the plastic and postitioned the cushion underneath. Inserted the new glide and drilled a hole in the plastic to accomodate the new rivet. Inserted rivet. Pulled the other end so it was tight holding the cushion and did the other end. Done.

Had to cut the glide 1/4 '' of the width to slide it through the existing slots in the panel.

This is the second time that this has happened with my dryer. The first time I replaced the thermostat and fuse, and it worked for a few years. This time I replaced the element and thermostat at first. Still nothing, then got the fuse; and walla just like new. Of course I lost a screw somewhere down at the bottom of the dryer, so there is only one holding the thermostat in place. Also I took off the front and cleaned out the lint traps; both times it was loaded with crap. Probably why it stopped in the first place.

Easy repair and I am not the handyman type. Unplug the unit. Lift the top. Remove 2 wires from temperature sensor and remove single screw to lift out the plate the sensor is mounted to(Easier to change the sensor out this way). Remove 2 wires from heating element and then remove single screw. Lift out heating element and replace with new one. Screw back in and reattach 2 wires. Remove 2 screws on the plate for the temeperature sensor and replace with the new sensor. Once 2 screws are back in the plate holding the sensor, screw back in with single screw and attach 2 wires. I called a tech and they wanted $125 just to look at the unit. When I read other reviews of how easy this repair was, I thought it was worth a try. Definitely saved us a bunch of money and time.

I loosened the belt removed the drum, removed the push nut and cracked pulley and replaced both,old push nut was a little stubborn but finally got it off.

I took the front off the cabinet (pry up front of top and remove two screws. Removed the drum, replaced the left rear drum support roller by removing one snap ring on shaft of roller and repacing after installing the new wheel. Reinstalled the drum, the hardest part of the repair was getting the belt back on the drum. It is hard to reach the belt to place it back on the motor. (small space to reach through) Being able to purchase a single wheel from this website saved me $50.00, the local suppier wanted to sell me a whole kit.