ABD2533DEB (ABD2533DEx2) Amana Refrigerator - Instructions

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

Installed new ice maker. It was easy - loosen two screws and unplug old wire harness. Put new unit in place. Did not realize new unit would not come with wire harness, but transferred old one to new ice maker (easy) and, "voila" some ice in 24 hours -- much ice since then. I am a 68 year old woman and it was "sort of fun" doing this job.

Well the frist thing I did was get out the all the paper work and look under trouble shooting.This frig has a list of codes to try to help narrow down what parts might be bad.Well at frist it seemed it was a Defrost Thermastat?Well thanks to PartSelect it showed me right where it was and step by step how to remove and replace it.It took me over 2Hr's,after that I let the frig run all night and the next morning(yep warm frig)not the part I needed,well now Im mad,the local part store said you need a 3in1 jump starter easy to in stall at $50.Can'nt bring parts back no way weather thier opened or not.So get home and can'nt see how this jumper is going to wire up to my compresser?So on to the Web site to get some info,find out that this part gets a thumb's down,it puts out more volt's then needed and kills your compresser the reviews where very help full.So back to PartSelect to see more info,then I spoted the Overload/Relay and went to the back of my Frig and this part just plugs right into the compresser,I pulled it of with pliers and Bingo a burn spot melted right through the Overload/Relay.Ordered the right part the same as the old one.Put the part in and Bam,compresser fired right up.If I only did alittle more home work I could off saved alot of head ach and money.Thanks PartSelect I'll alway's click on to your web site for future parts and advise.

removed ice maker and wire shelf. removed back panel screws and tilted forward. removed 2 screws holding motor bracket. swapped fan blade and reassembled

I called the repairman and he troubleshot the problem and told me that he could order the part or that I could. He quickly explained what to do. I ordered the part it came in with 2 days during that time I looked up on how to remove and replace the part on the website. The website stated it took around 15 minutes. That is all it took. I had to use a screw driver to remove two screws and seperate the connection. I reconnected the wiring per instructions on the website reversed the process and it was done within 15 minutes. I save a lot of money and time away from work. This is a grest site to get what you need to fix your appliances. If I have any problems with my other equipment I will becoming back to this website to get the parts and information

I want to thank you for providing the information and helping folks out that can do the job

replaced control board

first I looked into the refrigerator for blockage of air flow.
none found, I looked into the freezer area to see if fan was working ,it was, noticed ice built up on the outside of the metal cover letting me know it was not defrosting ,It was easier for myself to pull freezer door off , then the ice-maker,only three 1/4" hex head bolts,two 1/4" hex bolts only holding the metal cover . The quickest way to defrost was using a blow hair drier .once it was all defrosted I disconnected the defrost heater and using a volt/ohm meter,I ohm out the element,finding out I had no reading .The one thing I forgot to mention, unplug the frigertor first !!!

Removed two screws that held cover plate. remove cover plate. Remove water hose, and clamp, by compressing clamp with pliers. Remove fill tube by pulling HARD, from back.

Replace fill tube, check to be sure that it entered ice maker properly. Replace hose and clamp.
Replace cover and screws.

I didn't know what the plastic was - just that it was unappetizing. Reading other posts, it must have been the teflon coating. The refrigerator is 13 years old and reading other posts, I guess I'm lucky it lasted that long.

My boyfriend did the repair and here is his story:

The first ice maker we received was cracked on one corner. Not knowing how it got that way, I was concerned that there might be additional internal damage and that the unit wouldn’t work properly. Part Select was contacted and a replacement unit was sent with no difficulty.
As other reviewers have said, the replacement was quite easy, taking less than half an hour. The only tools I needed were a screwdriver and a nut driver. To begin, unplug the refrigerator and turn off the water supply to the ice maker. Loosen, but do not remove, the two top attachment screws. Then remove the bottom screw. Lift the unit up off the top screws and remove the water inlet hose at the top right. It’s probably a good idea to have a container handy to catch the small amount of water that comes out, but you’ll need a third hand for this.
The electrical wiring harness is very short and may be tricky to disconnect. On my refrigerator there is a round vinyl connector that plugs into a receptacle on the back wall of the freezer compartment directly behind the ice maker. This was removed with no difficulty (accidently, actually). Once the unit is out of the refrigerator you can remove the connector from the ice maker by using a screwdriver to depress the latch tab that is visible in a window in the unit housing. When installing the connector in the new unit make sure it is fully seated. Next, reconnect the round vinyl connector to the receptacle on the back wall of the freezer compartment. This was the worst part of the whole procedure. You have to support the unit close to the back of the freezer (due to the short harness) with one hand while inserting the connector with the other. This requires both arms in a confined space. The first time I did it I apparently didn’t get a good electrical connection on one end of the harness, and it didn’t work. Because the connectors are directly behind the ice maker I had to remove the unit and re-install it, but it was much quicker the second time, less than 10 minutes.
Once the connectors are in place put the water inlet hose into the opening at the top right. You may need to re-use the retaining clip from the old unit for this. Slide the two top mounting ears down between the screw heads and the back wall of the freezer compartment and tighten the screws. Then install the bottom screw. Plug in the refrigerator, turn on the water and make yourself a frosty beverage.
All in all, a relatively quick and painless procedure.

Another note - we kept saying "is there ice yet"? I think the metal bar that controls the ice maker needed to be raised and lowered a few times before it would work properly as it seemed to raise 1/2 way but the ice would not drop so I put it down and it worked its way up. Had to do it a couple of times over a 4 hour span but once going, it is working like a champ.

unscrewed to removed old and screwed in new

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

First I removed the 14.3 tons of freezer contents, closed the water valve, shut off the juice, and removed the freezer bins, the freezer door and the three screws that held the element in place. After bringing in 397 hand tools from my garage inventory, I loosened the unit and, after extensive evaluation, I finally disconnected the wiring connector from its freezer rear wall connector counterpart. You ain't gonna believe the rest of my story--of total ineptitude by an experienced fix-it-yourself dummy.

I searched the internet for a replacement ice maker and found it at partselect.com. I called Sears to ask if I could add my refrigerator to my existing appliance repair account. Sears said sure--it would cost me only one arm, three toes and one grandchild. I abruptly declined their magnanimous offer—I don’t give up my arms and toes so easily.

I visited the local Maytag repair parts and service retailer, who advised they didn't do parts anymore. Expecting their repair price would be greater than Sears, I resorted to partselect.com. I called them to be assured what I was buying was not mistakenly a 747 Landing Gear. On the afternoon (West Coast) of 4/28/10, I ordered (via internet) one PS21215123 Ice Maker Assy. Much to my pleasant surprise, it arrived via FedEX on 4/30/10 (no freight charges to me).

My repair/replacement efforts were hampered by the effects of my right rotator cuff surgery a few months before and major left wrist surgery two months ago to remove fractured bones and torn ligaments.

Undaunted by my physical handicaps, I forged forward. After re-installing the unit, I turned the water supply and electricity back on. It was graveyard dead. I wisely then bought two bags of ice as an interim solution to the severe needs of my wife and me for our daily chilled evening cocktails. I removed the unit, checked it out and re-installed it. I bought two more bags of ice. All the while, I turned the water and electricity off and on as required by reasonable safety standards. High tediousness!

Several more home maintenance tasks then arose for Sergeant Super Fixer, but I returned to the ice maker problem on 4/8/10. Last chance--remove the device and insure there was no frozen ice in the inlet tube--or call the local partsless repairman. No ice found, but I did learn the wiring connector to the unit was awry--no contact! While explaining that to my wife, I realized the two upper mounting screws were intended to be partially installed into the freezer wall to accommodate the unit's slotted mounting holes! Then, tighten the screws. Oh my God! During my 143 installations and removals, I had installed those screws blindly--using the (handicapped) skills of my right and left hands without any benefit of direct eyesight.

I returned to my challenging project this morning (4/9/10), fully utilizing all the expertise I had gained yesterday. Fifteen minutes of amusing effort! Turn on the juice! Turn on the water!Two hours later, ice cubes were dropping into the bin like rhinoceros bisquits in the jungle.

Hallelujah! I now am free for the next challenge!

HINT: Put a bed pillow (an old one, or your wife's) in the freezer compartment to soften the harshness of its cold metal on your back, if you use the "crawl in on your back" approach.

I just opened up the fridge back panel accessed the old relay/capacitor, pulled it out, replaced with the new one, snapped it back into place, tested it (compressor came on), replaced the back panel and went on my way. Really, really easy repair.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

Through out broken plastic, replace with new one
to be replaced in a few years.