9119598890 Kenmore Range - Instructions

I ordered the replacement clips from this site and they arrived in a timely manner. The clips were perfect, but due to the age of the oven, the holes had elongated and the new clips kept falling out also. I modified the clips by widening the tips with a pair of pliers. They are holding just fine. I don't think the older clips could've withstood the modification.

New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!

All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.

Unscrewed the heating element from the inside back of the oven and removed the housing cover from the back of the stove to access the terminals. (The unit had arked and fused the terminal to the connector.) Installed the new unit and replaced the housing cover on the back and screwed the unit into the back of the oven. Works like a charm.

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.

very easy remove the bad bulb install the new one

Open and slide door upward off of hinges. Removed bottom drawer to access hinge spring. Detached spring, noting proper hole in hinge for reinstallation. Removed three screws holding hinge and removed hinge. Compared new part to old...exact match. Inserted hinge, and reinstalled the three screws. Reattached spring in hinge hole. Slid door back down onto hinges. Done in four minutes flat!

Removed old hinges and installed new hinges.
Hardest part was determining that worn hinges were the cause of problem, then ordering replacements. GE website hinge on exploded view did not look like hinges I removed.Thanks to Google I got on to PartSelect.com website where excellent pictures of hinges and one-inch grid confirmed they sold exactly what I wanted for my 13-year old range, the model number of which was not even on the GE website.

replaced lights in refrigirator and freezer

1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.

I removed the control panel by removing 7 screws and replaced the light indicator and lens.

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

The plastic holes on the clock control panel had broken off so the panel would not hold firmly in place - the new clock control buttons plastic panel that I ordered was easy to replace since I had the four screws that held it in place to the front panel of the oven - only surprise was the new panel had black buttons instead of silver ones, but they look great on the oven front. Thanks for having the part and fast delivery.

Remove oven door from hinges, by pulling it straight up and off, (like you would do for closer access to clean inside). Remove the storage drawer. Lift up and away off the track, (like a file cabinet drawer). With the drawer out and away, you can see how the springs are easily detached from each hinge. Note the location of where the springs attach to the hinges, and bottom of stove. Remove each spring. Three screws on each side hold the hinges on. Unscrew, and set them aside. (The new hinges did not have new screws in package.) Place new hinge in place. Reinstall in reverse of disassembly. If any part of the door or face of the stove (where hinges mount) was bent slightly due to forcing door open, reform with light hammer taps and C-clamps. Enjoy for ANOTHER 10+ years, because it's a GE Profile Stove : )

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!