Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 9119333190 > Instructions

9119333190 Kenmore Range - Instructions

All installation instructions for 9119333190 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 9119333190
316-330 of 375
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Daughter Could Broil BUT Could Not Bake with the Oven

  • Customer: Joe from Burlington, CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
The ~60 minute time frame resulted because of: Locating & Turning off the Circuit Breaker (40 amp) in the Electrical Panel Box to the Oven (EXTREMELY IMPORTANT FOR SAFETY); Removing the Old Bake Element; Using a OHM Meter to Check the "Continuity" of the Old Bake Element to make sure that it was defective; Ordering the New Unit from Parts Select; Installing the New Bake Element and Calibrating the Oven Temperature Settings with a New Oven Thermometer. This was done for Safety and Cooking Reasons to ensure that the Oven would not overheat and was heating correctly. OTHER REPAIR HINTS FYI: I had to use a 1/4" Socket with a Ratchet to remove the Screws which were "frozen" in place; Upon installing the same screws I found that a Portable Hand Held Electric Ratchet worked great because of the "Arm Stretch" into the Oven; I secured the Power Wires that attach to the Bake Element i.e. to prevent them from slipping into the Oven Wall by securing them in place with a "loop" of #14 Romex Wire; Lastly, using pliers, I "VERY Lightly" compressed the electrical Spade Connectors (Female) from the Power wires onto the Bake Element Male Connectors to make sure that the wires were secure and could not easily disconnect.

Burned out Bake Element

  • Customer: Betty from Athelstane, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
This was my second time installing a new Bake Element, I am a 67 year old female, if I can do this anyone can. Used a pair of pliers, unscrewed screws pull out burned out element, release from wires, connected new bake element, pushed back in inserted screws...that easy all done.

Oven door difficult to open, would only open 4-5 inches

  • Customer: Thomas from Miami, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the video step by step, made the job simple and easy. Did not know there were springs attached to the lower part of hinge till watching video. Parts were genuine GE manufacturer parts which fit perfectly. Very helpful staff and great customer service. My model number did not match perfectly with others listed but the hinge part is identical.

Door hard to open and close

  • Customer: delbert from Auburn, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pull the door off the hinges. pull drawer out of range.Take sping off both frame and hinge arm. Unscrew three screws holing hinge in palce. pull old hinge out , put new hinge in . reinstall screws, spring, drawer , and door. Get the wife to make cookies.

Bulb Replacement

  • Customer: Judith from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Oven door wouldn't open/close properly; hinges offset & wheels broken

  • Customer: Bryan from Kentwood, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed YouTube video from PartsSelect. It was real easy to do and that video was helpful. Took off door by sliding it up off hinges, disconnected springs, unscrewed hinges & slid them out - reversed to install. Worked perfect, parts were exactly right and parts came within 2 days.

Bake Element Burned Out

  • Customer: Shane from Lenox, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Turned off breaker (Important!) => 2. Removed two (2) metal screws from element mount (1/4" socket or nutdriver) => 3. Pulled element out enough to disconnect wire connections from element (I bent mine up a little to keep them from disappearing back into the holes!) => 4. Connected each wire to new element then re-installed element into position => 5. Re-installed to metal screws (Do not over tighten!) => 6. Turned breaker back on then turned on oven. Element heated up quickly! You may notice a slight smell of something burning when you first turn it on, but that's normal and will fade quickly. Repair completed and $$$ saved!

The element caught on fire

  • Customer: Kay from Villa Rica, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
My brother -in-law unscrewed the old one , lifted it out. Put the new one in , clicked the wires back in , and replaced the screws. Did it all in about 5 minutes with one tool. Super easy!!

Drawer guide

  • Customer: Lee from Grass Valley, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Used Phillips screw driver, installed guide, applied lubricant.

the wires were not long enough to use the original path.

  • Customer: Ronald L. from Cedaredge, CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
the original path was from the right front control knob around the back of the range and left side of range,which i dismantaled to install the new wires to the right front burner. When I found them to be to short I had to also dismantal the right side so the wires could be routed there. The new wires worked fine but did take some extra time.

bake element shorted & burned into.

  • Customer: Emmett from Batesville, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
#1 I turned off power to stove. Removed two hex head screws that hold burner in place. Next carefully pulled burner out & disconnected the two electric wires that supply power to burner & hooked the wires to the new burner. Then carefully push new burner into place & install the two hex head screws that hold burner in place. Turn power back on to stove & the stove should be turned on for a short time to let the new oily smell burn off the new burner. Then you are finished & stove is ready to use.

Oven element burned out.

  • Customer: Ed from Boise, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed mounting plate from back of oven, disconnected spade terminals from old element. Reconnected spade terminals to new element, secured mounting plate w/2 screws...done.

Oven element split

  • Customer: Allyson from Holmes Beach, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the video instructions. It took about 20 minutes to remove the very old screws. Once that was done the rest of the installation took less than 10 minutes.

Replaced The Lower Element In My Oven.

  • Customer: Linda from North East, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I listened to the video instruction and did every thing he said to do. Was a piece of cake.

Oven baking element "popped", "flared briefly" and stopped working.

  • Customer: Vincent from Fenton, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I ordered the new baking element part for my 29 year old Kenmore oven. I followed your video instructions on the site to replace the old part. The step to remove (ie pull) the old part from the wiring was difficult, and I almost gave up on the matter. With some persistence I finally got the old part disconnected, and the remainder of the installation repair was easy. The new baking element part is shaped a little different from the original part, but it appears to work fine and the oven is now fixed. Thank you.
All Instructions for the 9119333190
316-330 of 375