Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 7MMSL0100TW0 > Instructions

7MMSL0100TW0 Maytag Washer - Instructions

All installation instructions for 7MMSL0100TW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 7MMSL0100TW0
211-225 of 330
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Out of balance, could't operate

  • Customer: Arlyn from Driggs, ID
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The prooblem started with the hole in the bottom frame, for tub spring wore through, spring fell off, then a spring retainer worn broke in 2 releasing 1 suspention spring. All springs were about to fail, metal very thin at at the contact points. Drilled a new hole for the new suspension spring, replace all 3 brackets, worn also, springs, and retainers with a small dab of grease at the contact points. The new springs mad the tub more stable than before the failure, and silent when spinning or washing. Be careful to get the springs in the right direction, then the spring comes over the outside the brackets and retainers, other way they rub in spots. On this machine one was backwards from the factory 18 years ago, surely that accounts for more stable running.

pumps water but will not spin

  • Customer: walter from grove city, PA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I did repair myself with your instructions. it was very easy to do for my age. 84.

Want spin

  • Customer: Kenneth from Jackson, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
As per partsselect.

would not spin in spin cycle.

  • Customer: paul from wardensville, WV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watch the video on the part ordering webpage.

Tub was slamming side of tub during spin cycle and getting all out of balance

  • Customer: Steven Arthur from Tifton, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took the cabinet apart really easily with Part Selects helpful video. Removed old suspension springs by removing outer brackets on two of them and by using pliers on the third one. The tub spring was totally missing. Put on two new brackets and springs with the nut driver. Then stretched the third spring into place. Replaced the tub spring by stretching into place and then put cabinet back together. All done very quickly!!! Now it works perfectly and runs very quietly.

Won’t go on unless the lid slams shut.

  • Customer: Steven from Moreno Valley, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First, unplug the unit. Remove the two screws on each side of the control panel on the back. They are located at the top corners of the unit. The base is held on by clips you press in on from the bottom. You will have to reach in over the tub and press in on clips, one each on the far side. At the left, you will be able to feel the lid switch, the clip is just to the left of the switch. It is about ½ inch wide, press firmly with your thumb. You may want to wear glove for this unless you like battle scars. Once done the control panel should hinge up. The switch is on the left side. To remove the switch, I first detached the wire harness to the control panel and unscrewed the grounding wire. Open the lid and the switch pulls right out. The new switch drops right in. Attach the wire harness and grounding wire. Place the control panel back side first at an angle making sure the back metal panel is lined up, once in place it should snap back in place when pressed down firmly. You might have to reach in over the tub again and pull the clip down (keep Band-Aids on hand). Plug the unit back in and you are good to go. Raise and close the lid, you should here the switch click on and off.

Washer would fill with water but would not run

  • Customer: Jeff from Lexington, KY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Broken lid switch. The BIG problem was trying to figure out how to remove the control panel. There was no screws on the back top corners nor two screws at the bottom corners. The front end caps was not removal either. Finally I found on the internet that if you slide a putty knife under front corner of the control panel you can push back the spring clip on each that will allow the panel to be removed and lifted up. From there the lid switch is located on the left side and is easy to replace from this point forward. You can read other instructions on details on replacing the lid switch.

My washer stopped spinning.

  • Customer: Jacob from Champaign, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I researched the troubleshooting on PartSelect.com and determined the clutch was going out on my direct drive Whirlpool washer. I ordered the part, found the instructional video that actually had my exact washer being worked on, I followed all of the steps of replacing the clutch and in a snap, my washer was spinning. I've worked in apartment maintenance for years and PartsSelect.com has always been my only resource for appliance parts and repairs. The prices are great (I've compared most parts websites and 8 times out of 10, partsselect.com is cheapest), the shipping is extremely fast and the parts are alway right. Great site!!!!

Washer shook in the SPIN cycle.

  • Customer: Mark from Dagsboro, DE
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Follow the video to remove the cabinet. Did NOT have to lay the unit on its back in order to replace all 5 springs. These may be easily replaced with the washer standing upright. The back Suspension Spring was removed by using the access hole in the back of the washer to remove the screw holding the back spring bracket in place. Reassembled the cabinet per the video. Except for moving the washer around, this was an extremely easy repair. To facilitate moving the washer - use Moving PADS placed under the 4 feet of the washer.

Machine wobbled during spin cycle. Appeared to have some loosened part in the rear of the machine (noted some flexing on the front of the cabinet during spin).

  • Customer: Jonathan from Brandon, VT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Disconnected electrical and then water inputs on the rear of the cabinet. Tipped the machine onto its front. Found that a spring was unhooked and dangling from a bracket. I searched for the location to secure the spring and found a hole on the rear base of the cabinet rusted through. I drilled another mounting hole nearby, Since the original spring had also broke, I replaced it with a new one from PartSelect, securing it between its bracket and the new retaining hole. Returned the machine to its upright position, reconnected water input lines, then its electrical. The machine works fine once again.

Washer stopped running. Would fill water and stop.

  • Customer: Jen from LINCOLN CITY, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged washer, took out screws that held on the dial panel, lifted dial panel, disconnected the ground wire, released the clip, lifted the lid which released the switch. Installed new switch closed the lid which holds it in place set the clip connected ground wire reattached dial panel secured it with the screws, plugged the washer back in and I was on my way the conquer that pile of laundry that had built up.

Auger would come completetly off when taking out clothes. The rubber washer had disintegrated.

  • Customer: Jennifer from Wake Village, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I watched a Part Select video on replacing the augitator and just followed the directions to replace the thrust washer (which was showing wear) and the washer. The instructions that came with the thrust washer were helpful as well.

The Lid Switch Broke And The Washer Stopped Working.

  • Customer: MERANDA from ELIZABETHTOWN, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
First, I moved the washer with water in it from the wall. Then, I removed two screws with a phillip head screwdriver from the back cover to the controls. Then I used a little bitty wrench to remove two small bolts that also held the back cover of the controls to the rest of the washer. The control panel was all attached, so it had to lay forward on the washer to remove the broken lid switch and then to install the new lid switch. There was one screw that I removed with a phillip head screwdriver. I removed the broken part and placed the new part into the hole. Then I had to move the control panel with limited space to lift the lid of the washer; the part would not fit property without lifting the lid. Once it fit into place, I closed the lid and replaced the screws and bolts. It worked beautifully. Thank you for your online help and the remarks from other people who had previously fix this lid switch.

Stop Agitating

  • Customer: Glenn from Wheaton, IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Leaned the washer back to get at the bottom, removed the water holes, removed the water pump, removed the motor, replaced the direct drive motor coupling. Put it back together and it's all good. No clutch or drive problems. Simple fix.

Tub will not spin, agitator does not work. Already replaced the drive coupling

  • Customer: Raymond from Chagrin Falls, OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I generally followed the video. Disconnected the water hoses, removed the front, laid the washer on its back. My water pump is rusted onto the motor shaft so I left it in place. I removed the water pipes from the pump then removed the pump/motor/gearbox as one unit. Watch out for more water than you think being released from the pipes and pump!! Everything works well with the new clutch fitted.
All Instructions for the 7MMSL0100TW0
211-225 of 330