Maytag/Maytag_Thumb/OBEL0PDR.gif
See part 2 in the diagram
Replacing your Whirlpool Washer Agitator Cap Barrier with Seal play video
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Agitator Cap Barrier with Seal

★★★★★
★★★★★
10 Reviews
$9.11   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11748113
Manufacturer Part Number WPW10074580
Manufactured by Whirlpool
Product Description

Agitator Cap Barrier with Seal Specifications

The O-Ring is included with this cap. It can be purchased separately as Part #WPW10072840.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will not agitate | Leaking | Does not dispense fabric softener or detergent | Noisy
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Whirlpool, KitchenAid, Maytag, Kenmore.
Part# WPW10074580 replaces these:
AP6014843, 285551, 3347290, 3354733, W10074580
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

2 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Danny
    January 18, 2018
    No the washer tub went washing some time get's unbalance and start beating&banging and now some water leak's out
    For model number wtw4800XQ2 washer
    Hi Danny, Thank you for your question. If the tub is shaking and banging, there are some parts that you will need to check to see which one is causing the issue. You will need to check the agitator directional cogs, the suspension rods, the suspension rod supports, the springs, the drive block, the inner seal cap, the rod supports, the agitator, the levelling legs and the clutch assembly. I hope this helps. Thank you and have a great day!

    3 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Robert
    July 22, 2019
    What's wrong when the machine is on spin the whole machine move across the floor banging
    For model number WTW4800XQ4
    Hello Robert, Thank you for the question. I suggest checking the Suspension Rod Kit, PartSelect Number PS11703290. The rods keep the tub balanced and from banging around. Hope this helps!

    Was this helpful?
    Thank you for voting!
    Related Parts:
      Part Videos

      Replacing your Whirlpool Washer Agitator Cap Barrier with Seal

      Replacing your Whirlpool Washer Agitator Cap Barrier with Seal play video
      Customer Repair Stories
       Average Repair Rating: 4.0 / 5.0, 29 reviews. What's this?
      Sort by:
      Sorry, we couldn't find any existing installation instruction that matched.
      upper portion of 2-piece agitator didn't spin
      Popped the agitator cap with a flathead screwdriver. Removed the dust cap, tearing the o-ring in the process. Removed the bolt that holds the agitator in place, removed the whole agitator. Pulled the top portion of the agitator off, removed the dog housing and all pieces of the broken dog pieces. Replaced them, and put it all back together in reverse order. Pretty straight forward repair. Works great!
      • Kevin from Everett, WA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        1- 2 hours
      • Tools:
        Screw drivers, Socket set
      • Parts Used:
        WPW10074580, 285751
      38 of 40 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Ratchet assembly in upper half of agitator would not engage.
      Fabric softener dispenser snaps in. Apply sideways pressure to snap out. Reach inside agitator and remove agitator cap barrier seal by pulling on tabs. Using socket with extension remove center bolt and rubber seal. Remove upper agitator assembly. Follow instructions provided in agitator repair kit to replace and re-install ratchet ratchet dogs and carrier. Reassemble in reverse of disassembly. Note: Apply a small amount of liquid dish washing detergent to agitator barrier cap seal to ease in re-installation.
      • David from Jonesboro, GA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Socket set
      • Parts Used:
        WPW10074580, 63580, 285811
      15 of 612 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Upper Agitator & cogs wore out
      I pulled the cap and took a socket wrench turned the stud agit off and removed the upper agitator. Than I assembled the new agitator with the new clogs put the agaiator back on and tightened the stud agit. Replaced new cap and done! Easy job!! Everything is working like new again. This whirlpool washer is 14 years old and still going strong!
      14 of 24 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Top half of agitator not working
      Although this was listed as 'a bit difficult' and talking a bit longer than normal, this was because the agitator cap had leaked, and over time the agitator bolt had become completely rusted such that a socket simply couldn't fit. Due to the tight confines, I also could not get a needle-nose vise-grip to hold on to the nut, so attempted to drill out the bolt. This ended up being a problem, but it turns out that drilling AROUND the edge of the bolt and through the edge of the plastic allowed me to remove the top of the agitator, which then allowed a normal pair of vise-grips to be used to remove the bolt. Once the bolt is removed, everything simply fell into place, and the overall job 'should' have only taken a couple of minutes and been 'really easy', except for that rusted-out bolt.
      • David from Mission Viejo, CA
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver, Pliers, Socket set
      8 of 11 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Upper agitator would not move
      Begin by removing the fabric softener dispenser then the barrier cap can be pulled from the agitator this will allow access to the agitator retainer bolt use an 11mm socket and extension to remove it once the bolt is out the agitator assembly can be pulled straight up out of the machine. To separate the upper agitator from the lower placing the agitator on the floor and placing your feet on the lower half and pulling up on the upper half will separate the two parts, however before performing this operation the agitator cam assembly may be heat set in place, looking down into the upper agitator there are four lugs that hold the cam in place if you use a sharp knife and cut thru the areas that have been heated and welded together separation of the two half's will be made easier. Once all the old cam parts are out reassemble the new parts the same way as the old ones were removed, the cam kit and the thrust washer kit come with a diagram in case you forget how to reassemble the parts. The agitator assembly simply slips back onto the drive splines, the attachment bolt has a seal under it that can be crushed if the attachment bolt is tightened too tight, I could not find a torque specification for this bolt so what I did was tighten the bolt until it contacted the seal completely and then applied just enough torque to turn the bolt until the agitator began to turn along with the bolt, then just install the barrier cap and seal and replace the fabric softener dispenser and the job is done, if you're washer is like mine I spent more time cleaning parts than actually performing this repair.
      4 of 4 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      agitator did not turn
      I removed the cap over the ratchet mechanism, removed the ut holding the agitator in place, removed the agitator and cleaned all the parts. The assembly for the ratchet dogs was a 3 piece assembly that was included in the kit I bought from Part Select. I also bought a new cap and gasket since my old gasket had broken too. A new gasket was already included in the kit, so I didn't need ot buy the cap. I liked that th ekit included everything I needed and good instructions. parts got to me in about 3 days. Very happy with my Parts Select experience and the fact I saved at least $100.
      • Mark from Whitehall, PA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver
      • Parts Used:
        WPW10074580, 285811
      4 of 6 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      The washing machine was making a loud noise
      I unscrewed the agitator and pulled it out. Then took out the old agitator cam kit and put in the new one.
      • Duane from South Deerfield, MA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Socket set
      • Parts Used:
        WPW10074580, 285809
      3 of 4 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Found seal had split on agitator cap
      I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.

      Thanks for making finding part so easy . . . .
      • Kim from Cleveland, OH
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        Less than 15 mins
      • Parts Used:
        WPW10074580
      3 of 4 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Top portion of agitator wouldn't turn.
      First I removed the top cap on the agitator, then I removed the second cap inside the agitator. I moved the agitator with my hands and saw that the "dog ears" were worn and no longer touched the agitator and couldn't move it. I then used a nut driver to remove the nut that held the top portion of the agitator onto the bottom portion. I made a note of the worn parts, got online at PartsSelect.com and ordered the replacement parts. A few days later the parts arrived and I repeated the above process in reverse using the new parts. It now works like new!!! It wasn was very easy. Thanks!!!
      3 of 5 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      no agitation
      Removed agitator found the agitator dogs were broke, identified all parts needed ordered from PartSelect, recieved all parts , repair was very simple 10 min job , works great! Saved lots of money !
      2 of 3 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      10 Reviews
      5.0
      Filter By Rating:
      • 5 Stars
        10
      • 4 Stars
        0
      • 3 Stars
        0
      • 2 Stars
        0
      • 1 Star
        0
        Sort by:
        Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
          Model Cross Reference
          This part works with the following models:
          PartSelect Number: PS11748113
          Manufacturer Part Number: WPW10074580
          Brand
          Model Number
          Description
          Kenmore
          11016922500
          Washer
          Kenmore
          11016922501
          Washer
          Kenmore
          11016922502
          Washer
          Kenmore
          11016922503
          Washer
          Kenmore
          11016922504
          Washer
          Kenmore
          11016942500
          Washer
          Kenmore
          11016942501
          Washer
          Kenmore
          11016942502
          Washer
          Kenmore
          11016942503
          Washer
          Kenmore
          11016962500
          Washer
          Kenmore
          11016962501
          Washer
          Kenmore
          11016962502
          Washer
          Kenmore
          11016962503
          Washer
          Kenmore
          11016964500
          Washer
          Kenmore
          11016964501
          Washer
          Kenmore
          11016964502
          Washer
          Kenmore
          11016964503
          Washer
          Kenmore
          11016972500
          Washer
          Kenmore
          11016982500
          Washer
          Kenmore
          11016984500
          Washer
          Kenmore
          11016986500
          Washer
          Kenmore
          11020052990
          Washer
          Kenmore
          11020052991
          Washer
          Kenmore
          11020056991
          Washer
          Kenmore
          11020072990
          Washer
          Kenmore
          11020092990
          Washer
          Kenmore
          11020096990
          Washer
          Kenmore
          11020097990
          Washer
          Kenmore
          11020112310
          Washer - AUTOMATIC WASHER
          Kenmore
          11020112311
          Washer - WASHER

          Get in touch, we're here to help!

          Open until 1am EST

          Contact Customer Service