Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old valve failed and started to leak.
Pulled off the old valve using a crescent wrench and screw driver. The replacement part was a 100% exact match. Slapped on the new valve and that baby was water tight. $50 on a new valve is a lot better than $500 for a new washer.
Partselect.com was so easy to use and find the right part. Way more helpful than whirlpool's site, but that's not surprising seeing as they have an "authorized repair technician" page.
Washed the edges good and clean to remove old tape that was holding the old panels. Slid in the new ones and found that the retaining strip would not work without replacing the inner strip. I didn't want to order this $53 dollar plastic strip so I squeezed a couple of rubber pieces into the bottom of the side edges to hold the top panel. Placed the retaining strip in place and used a long strip of black duct tape at this bottom edge to hold it all. It works and the new panels make the dish washer look close to new,the black duct tape hardly shows. This works good for my 10+ year old dishwasher until it is replaced with one that has a better door design.
These access panels are just plastic. My son's big 10 foot stepped into it and busted the holder for the screw. This was the 2nd time we had to replace this part in 4 yrs. I was very glad to find it again.
The easiest way to change this out is to remove the access panel(like the one you purchased) and the metal brace that supports it to the bottom metal access panel. To do this, REMOVE the screws in between the door and access panel. Step 2: LOOSEN screws that connect the metal braces together. You do not need to remove them completely as the middle brace slides up. You should now have the panel and brace together in your hands. Step 3: Using a flat screw driver pry (and I mean pry!) the retainers out of the catch. At this point breaking the old plastic is a better option than bending the metal! Once removed, your ready to swap out the front cover of the panels and put'er back!! Good Luck!
Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.
removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.
The upper spray arm was cracked where it mounted to the top rack.
Ordered a new upper spray arm from PartSelect. Shipping was fast and the correct part was recieved. Use a hair drier to warm the prongs that mount to the upper basket. The plastic is softer and will squeeze/fit in place without snapping off the "ears".
remove star screws holding inside door panel. remove plastic cover that protects latch assembly. hook one end of spring on stationary pin on inside of slider bar. Hook other end of spring on pin on slider bar. replace cover and door panel.
Replaced door gasget took 5 minutes tops. Ran cycle and still had leak. Called local repair person. After thoroughly checking out the dishwasher and running soapless cycle determined problem to be soap build up over time. He ran a commercial cleaner through a complete pots and pan cycle. No more suds and no more leak repair complete. Did not actually need door gagset but it was super easy to change and delivery service was great.
I watched the video link sent in an email and followed exactly what they did in the video. I removed the star head screws holding the door liner in place. Then removed the protective cover on the inside. I disengaged the component holding the latch in place. I replace the component that holds the latch in place and then snapped the new latch in place. I turned the dishwasher dial until the prongs were fully retracted. I replace the protective cover and then put the door cover back in place. I initially only placed the left bottom star head screw until I was sure that the latch was going to release. I tested that it was working properly by slowly turning the dial on the dishwasher control. Once I knew it was working I replaced the rest of the screws.
removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.