Replaced the speed control plate and phase control board and works well. Pay attention to speed control board spring and adjustment lever when reassembling.
Pulled off end cover. Used the how-to video's to show me how to remove the (3) components (watch out when it comes to removing the spring). Removed all (3) components (one issue was the black cardboard seal, which because of its age broke. Hindsight tells me that I should have purchased a replacement seal along with the (3) new parts. Fixed the broken part of the seal with scotch tape). Installed all new parts with the help of the video's and put the cover back on. Even with the new parts, the mixer would not run. Come to find out, after I took it to an appliance repair person, that someone had pulled both brushes and put them back in improperly. I could not find a how-to video that showed me how to de-install/re-install the brushes properly. I assume that was because new brushes were no longer available for purchase. At any rate, when the brushes were put in properly, everything worked. The repair person also adjusted the (2) screws on the speed control plate so that when you change the speeds via the lever, it all works properly. I didn't find a how-to video covering those adjustments either.
I removed one screw on back, once inside mixer I removed the ground screw then pulled off the black and white push on caps, then I reversed everything to get it installed, very easy
Old screw cap wore out and would not hold bowl when mixing heavy batters.
Unscrewed old Screw Cap, tapped it out with hammer. Replaced with new screw cap that was slightly different and tight. Tapped it in with piece of wood over it and hammered it on. No problems.
Mixer would slip gears under load, finally would not mix under any load
Rather than duplicate previous repair works, I recommend going to this user site and follow their instructions: http://www.neilcrockett.com/mixer1.htm. Once you have done this repair, taking the unit apart is easier to perform this tasks. Order replacement Grease "Benalene 930-2" in the 3.3 oz container and be sure to use the full container to lather all around all the gear components so grease will be available to units for years to come due to heat build up under load. Too, the 3.5 oz container is made for one unit repair job and is available through Amazon. This grease is available on larger quantities if needed / desired. I did order both, a Worm Gear and the Worm Gear and Bracket as I wasn't sure of my mechanical ability to make this repair until I got inside the unit but the worm gear is easily replaced once you clean out all the old grease. The worm gear is a neoprene type gear with all other gears being metal. I assume neoprene is used as sacrificial to save other gears from breaking under loads and years of use.
I removed the spring loaded brush screw on the side of my mixer and lost it the next day. I found a schematic of this part on your website and ordered the four pieces that make up the brush screw(?). They arrived in just a few days and I referred back to the schematic to put it together. I then popped it in my mixer, screwed it down, plugged her in and away we go! Easiest repair I’ve ever done! I’m a 70 year old retired lady and not very handy, but this was an easy fix! Thank you, PartSelect!
Mixer would only run Full Fast. Could not determine cause or fault.
1. Removed the mixer back plate Cover. 2. Removed the Speed Control Plate and retained spring, wires and ground wire. 3. Removed the old Speed Control Plate screws. Noted Control Plate pitted contact. 4. Removed old Triac Phase Control Board. 5. Removed old Governor. 6. Installed new Governor. 7. Installed new Phase Control Board. 8. Installed new Speed Control Plate and retaining spring. 9. Reattached Speed Control Plate wires. 10. Adjusted Speed Control Plate Screws and set mixer speeds from Stir to maximum settings. 11. Replaced Motor Brushes on left and right side of mixer. 12. Reinstalled mixer back plate cover.
bowel would come out of screwcap when making dough for pasta
The repair was easy only requiring a phillips head screw driver to remove the old screw cap. The new screw cap fit snuggly and required a little downward pressure from my hand to seat it. Then I simply tightened the screws. Good as new for this 30+ year old mixer. My wife loves this mixer that was given to her by her Aunt. Glad we could keep it going.