Motor Brush WPW10380496

Got a harvest gold mixer from g maw and thought a project would be nice we have several of these mixers in the family i knew a 2 prong cord was not safe so i took apart the mixer and wanted to regrease it just give a lookie to see what i needed and then i decided after watching video on y tube to convert to a solid state.

Parts select as a whole has been very understanding as a whole and i will continue to get parts thru them they are genuine parts which is something i had to have i have 90% of my parts for a full overhaul we just cannot get the parts delivered fedex and usps i specify the address and they deliver 2 blocks east of the house thanks for honest neighbors usps was late as usual like i said parts select is outstanding at placing the order and appliances can be fixed super simple with the right tools the concern is with the fedex and usps now they are shorthanded but lets be real but when you deliver a package just triple check it is the right house !

I followed the instructional video linked to my email order confirmation. Partselect provided one of the best how-to videos I've ever seen. With the right tools, a little patience and the video, I had an outstanding repair experience.

Found control backplate out of adjustment. Should be nominal 3/8".Broken speed control spring which attaches to backplate bottom.
I recommend Loctite Blue to complement locknut's when adjusting RPM of "Stir" speed

followed the emailed instructions from your company
worked perfectly
thanks

The brushes are located on each side of the tilt head of the mixer. I used a screwdriver to remove the screws, removed the brushes & replaced with the new ones. Runs great again!!

I removed the spring loaded brush screw on the side of my mixer and lost it the next day. I found a schematic of this part on your website and ordered the four pieces that make up the brush screw(?). They arrived in just a few days and I referred back to the schematic to put it together. I then popped it in my mixer, screwed it down, plugged her in and away we go! Easiest repair I’ve ever done! I’m a 70 year old retired lady and not very handy, but this was an easy fix! Thank you, PartSelect!

Removed the rear cover to inspect the speed board. Replaced motor brushes and noticed the motor body nuts were loose and 1 was completely off. Cleaned up speed board and replaced the motor body nuts, tightened with nutdriver, adjusted speedboard governor screws and with new motor brushes worked like a charm. The very rough sounding motor noise was gone and the mixer has not operated so quietly ever.

1. Removed the mixer back plate Cover. 2. Removed the Speed Control Plate and retained spring, wires and ground wire. 3. Removed the old Speed Control Plate screws. Noted Control Plate pitted contact. 4. Removed old Triac Phase Control Board. 5. Removed old Governor. 6. Installed new Governor. 7. Installed new Phase Control Board. 8. Installed new Speed Control Plate and retaining spring. 9. Reattached Speed Control Plate wires. 10. Adjusted Speed Control Plate Screws and set mixer speeds from Stir to maximum settings. 11. Replaced Motor Brushes on left and right side of mixer. 12. Reinstalled mixer back plate cover.

I removed the excess of grease to clear all parts. Then I installed new mechanical parts. Finally, I installed all electrical parts. I followed a logical sequence of removing and installing steps. Tip: Never remove parts without a logical order of sequence.

I decided to update the motor brushes in our KitchenA id mixer even though it operated perfectly for years. After installing the motor brushes, you sent,I plugged the cord attached to the mixer into the outlet. I selected 1 on the speed selector and nothing occurred. The mixer would not operate. I then checked the outlet to insure there was voltage present; there was voltage present. I again plugged the cord of the mixer into the outlet, selected 1, then 5, and finally 10, with no results. The mixer would not operate. Finally, I removed the motor brushes I had received from you and installed the old brushes that were originally in the mixer, plugged it in the outlet, selected 1 and the mixer operated perfectly as it did BEFORE installing the brushes you sent.