10654536400 Kenmore Refrigerator - Instructions

Been fighting this for over a year. Sometimes the fridge and freezer would heat up past the point it should come on. Had to slide the fridge temp control back and forth until the unit came on. Researched the problem determined the thermostat to be the issue. Got the part, finally found the time, then took the top tray out, popped off the escutcheon, unplug some wire and took out the control shuttle. Removed the old and replace with the new thermostat. Re-installed everything, plugged in it in and BAM. It's working. Now just fine tuning the slides to desired temps. THANKS PARTSELECT.

With the new Ice Guide all I had to do was a use a small screw driver to help guide the tabs into place and I was finished!

This is for the refrigerator, not the freezer door which is more complicated. First empty the refrigerator door of food and removed the shelves. Remove the hinge cover on the top hinge by removing one bolt. Then, holding the door, remove the top hinge by removing the three bolts in the bracket (not the bolt in the recessed hole). Lift the door off the lower hinge and lay the door on its edge on the floor. Pry the old Door Cam out of the hole in the door with a knife (my Door Cam was ground completely flat). Insert the new Door Cam. Remove the old Lower Door Cam from the lower hinge and insert the new Lower Door Cam. Pick up the door and lower the door onto the lower hinge ensuring the lower hinge pin inserts into the hole in the Door Cam on the door. Reinstall the upper hinge and insert bolts without tightening. Align door and then tighten hinge bolts. Reattach top hinge cover and tighten the single bolt. Test the door to ensure it closes and stays closed. I had to remove the door a second time to rotate the Door Cam slightly to ensure cams were better engaged (tongue in groove style) when the door was closed. Reinstall the shelves and load the door with food.

replaced the valve

The replacement part (new ice maker unit) orked perfectly fter insstall. The "Part Select" video on how to replace this unit was extremely helpful and actually convinced me to try it myself. I took the old unit out and just reversed the process and installed the new, replacement unit. Worked fine and wroks fine. (Note: it did take a full 24 hours or a little longer to actually start making ice. I think the ater supply drains off and takes a while to get back into the ice maker.)

Removed (snap on)removed screw, and ice dispencer side (door and Pin) You have to assemble to reinstall (not easy to install while assembled) Install the pivot pin the rest of the way with the new spring mounted and when unit is almost in place, install the pivot the rest of the way, install tension hold downs that old both the water and ice dispenser shafts, reinstall cover, reconnect wiring and test, I had to remove the plunger because the water wouldn't shut off fast enough. Unit works great now.

Put in new motot and control

Replace the auger drum. I had order it and the auger, but I did not need the auger. I returned the auger with ease. Parts Select will always have my business.

The plastic control bracket would not "lock" in place because the plastic detentes broke, not allowing the ice maker dispensing 'paddle' to engage the micro switches that allows the ice maker to eject ice. An easy repair of replacing the entire plastic control bracket.

After our four year old refrigerator door wouldn't stay closed as a do it yourself kinda gal I found this website that assisted me in an easy and inexpensive fix. The "plastic" yes, "plastic" piece on the bottom of the door was worn down to nothing. My only suggestion is to call in your order, the customer service folks will help you order the right cam for your model. The next thing is to change both cams if you have a side by side. We changed the fridge side which fixed the problem, then realized the cam on the freezer needed to be changed to make it level. Great customer service!

exactly as shown on the video and it was completed in less than 10 minutes with only a nutdriver; took wife to dinner with the money saved and returned to find ice in bin without the "iceberg" from the prior leak! Thanks for the great parts selection, clear description of problems to help select correct fix and most of all the "how-to" video. I'm a customer for life ! WSD

Removed 3 screws pulled out the old part and replaced it with the new one. Then plugged in the refrigerator and the repair was complete.