Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
This is the burner head and electrode for your gas range. If your gas igniter glows but will not light, or if the element will not start or heat entirely, you may need to replace the burner head. This burner head is approximately 4¼ inches in diameter and is sold individually. Please note that the mounting screws for this burner head are sold separately. To replace the burner head, simply unscrew the old, defective burner head and screw in the new one.
How Buying OEM Parts Can Save You Time and Money
Why buy the real thing?
OEM stands for Original Equipment Manufacturer. Simply put, this means that the company who made your appliance is also supplying the replacement part for it.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Sam K - April 19, 2019
Verified Purchase
Easy repair-almost
Part was great; all one does is unscrew two screws, slide off connector to the electrode, attach electrode to new burner, drop in and screw into surface.
The potential problem is getting the screws out. If they are rusted or the top hollowed out, you may have to carefully drill out the old screws, without drilling too far. Narrow area to get vice grips onto the screw heads. That was very tedious and time consuming.
★★★★★
★★★★★
MICHAEL S - March 30, 2021
Verified Purchase
I'm cooking again!
Exactly as described. Easy install. Works perfect.
★★★★★
★★★★★
Gian D - September 11, 2019
Verified Purchase
Easy replacement
Burner would click and take time to ignite which caused gas build up and safety concerns. Ordered and replaced the burner using two screws, now it works like new! Easy fix.
★★★★★
★★★★★
Lyle F - February 5, 2020
Verified Purchase
Works great
Our stove top burner has been difficult to lite for some time. We decided to try to replace the igniter. Wow It works like it should now. Sure am glad we decided to do it. Replacing it did take a little effort as we had to use oil to get the screws out but after they can loose it was very easy.
★★★★★
★★★★★
William C - June 21, 2018
Verified Purchase
Very easy repair
Part works great
★★★★★
★★★★★
Dave H - March 3, 2020
Verified Purchase
Easy repair - the part was a perfect match. I only had to replace two screws and reconnect the igniter that was included with the part.
The part was a perfect match for the original burner. The cook top is a good as new with the replacement part. I'm sure an appliance repair company would have charged a couple of hundred dollars for the service call and part replacement. I did it the labor and the part cost me approximately $60 and works great.
★★★★★
★★★★★
Steve F - April 28, 2018
Verified Purchase
Perfect fit, exact replacement
Great part, fast shipping
★★★★★
★★★★★
Mary E S - July 11, 2019
Verified Purchase
Easy repair
Part working great ??
★★★★★
★★★★★
Steve R - July 20, 2019
Verified Purchase
Correct parts for me
Exact right part. Once I finally got the old one apart (corroded screw heads had to be drilled out), reassembly was a cinch. Works great!
★★★★★
★★★★★
Bronwyn K - April 8, 2019
Verified Purchase
Easy
Took 15 minutes. Very easy fix.
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 3.7 / 5.0, 11 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Auto igniter had gone bad.
Take out 2 T15 torx screws. Lift burner assembly, disconnect igniter. Make sure wire does not return into hole. I put A paperclip on it. Connect new burner assembly. Clean under old burner. Install burner assembly with screws. Test burner. Voila!
Aubrey from EADS, TN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Worn Burner Head Screws
Wanted to deep clean the range, but popped the worn screw heads on both the burner mounts and igniters embedded in the chassis. The way the range is designed, the bolts extend through the glass top and into the burner orifice. The bolts were unable to be extracted so replacement was the only option outside of a small third party machine s
... Read morehop. The double burner is discontinued and impossible to find, will replace this "High-End" POS when we remodel.
Removed Burner Heads Disconnected igniter Leads Extended range to remove glass top Removed glass top mounting screws CAREFULLY Removed Glass Top (REPLACEMENT = $800 Min) Removed affected burner orifices Tracked down parts list and maintenance manuals Tracked down similar issue: https://www.youtube.com/watch?v=YfCLJ1rXK6w&t=114s Replacement bolts : #8 24 X 0.5" Sheet Metal Screws Ordered Replacement parts and installed in reverse
This is the 3rd burner head that was replaced . everyone had the screws break off , & had to be drilled out & re tapped .I would not purchase the replacement screws @$4.00 each . They were just plain sheet metal screws that were steel . Better going to a home center & purchasing brass or stainless machine screws at a 1/4 of the cost .If y
... Read moreou are not familiar with drilling out broken screws ,then this is not the repair for you .
Read less
Mike from LIVINGSTON, NJ
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
5 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace X-Large Burner Head with Electrode
Disassembly: Removed 2 screws with nutdriver. Pulled off electrode connection. Screws were rusted and needed replacement.
Assembly: Slipped on electrode attachment. Went to local hardware store and bought 5/8" 8/18 pan head screws. Used screwdriver to screw down burner head. The 3/8" inch screws on the tech sheet do not wo
... Read morerk. Too short and flange is too wide to fit in opening in burner head.
Installing the 2 new burner assemblies worked great with the new screws. New screws however, did not work with the old burner assemblies that have rusted screws I wanted to replace. New burner assemblies are slightly taller that the old ones.
I first tried to remove the torx screws only to have them break off..soooo as with most home repairs it grew into a bigger task. 1) unhooked the gas line and unplugged the unit 2) place the unit upside down on workbench 3) used a socket set to remove the hex screws that held the top on 4)removed all the other burners and disconnected ele
... Read morectrical wire connected to the igniters. 5) Removed the top 6) uses pliers to remove the screw parts left in the burner base (wd-40 and lock wrench)..Replaced the old gaskets 7) put the top back on and screwed the top back on (make sure you pull the igniter wires through the top before securing it) 8) Reseat and screw in the burners using a torx bit
Removed the two fastening screws with a small square head screwdriver,lifted the burner head disconnected wire from damaged electrode. To install just reversed the steps,total time less than ten minutes.
jose from san juan bautista, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
3 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
electrode broke, screw broke
The ceramic on the electrode broke due to water over boiling the week of Thanksgiving. When i tried to loosen the screw to replace the electrode it broke off inside the threads. Ordered whole new unit overnight. Back in business in five minutes. Thanksgiving was back on!! Thanks!
Unscrewed burner assembly and removed wire. Unable to remove electrode screw. Striped head of screw. Tried penetrating oil but no luck. Tried to drill and use easy out bit but ruined burner assembly and had to order new burner assembly. When assembly came it had electrode in place but website does not show electrode with assembly except o
... Read moren one burner. With mail and all it took about a week to fix 2 burners. Returned unused electrode for credit. Overall, cheaper then a service call by far.
Read less
W E from Camden, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
4 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
8 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ellen
November 12, 2017
Is this the part for the front right burner (the larger of the 4 burners measure 4 1/4" across). That is the burner head we need to replace. The current igniter sparks but does not start the burner every time causing gas smell). (we did order the burner electrode part #ps11744318 back in july 2016 order #9022918 and tried to install it. But the bracket that holds the electrode cannot be removed from the old burner head to install the new part
For model number JGD8430ADS
Hi Ellen,
Thank you for your inquiry. Yes, this is the correct burner for the right front. I hope this helps. Thank you and have a great day!
13 people found this helpful.
Was this helpful?
Thank you for voting!
Ron
January 13, 2018
Does the burner head with electrode come with the 2 screws to mount it to the cookktop?
For model number JDG8430ADN
Hi Ron,
Thank you for your question. The screws for the burner heads are sold separately. The part number for the screw is PS11742240. I hope this helps. Thank you and have a great day!
6 people found this helpful.
Was this helpful?
Thank you for voting!
DALE
March 19, 2018
When we turn on a burner, the other three burners' electrodes will start sparking, too. The burner does light up but the other three continue to spark without ever going out.
For model number JGD8430ADB
Hi Dale, Thank you for the question. This sounds like an issue with the spark module, PartSelect Number: PS11744407. This Module controls the sparking to all the burners. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Judy
May 6, 2018
What is the best way to clean the burner rather than replace it?
Hi Judy, Thank you for the question. For daily maintenance and light grease stains, use vinegar in a spray bottle and spray the burner with vinegar and allow to sit for 10-15 minutes. Wipe down with a clean cloth. This method is most effective as ongoing daily maintenance, as it cuts through grease before it has a chance to be baked in. For harder grease stains and grime, wash all burners with lukewarm water and dish washing detergent to remove initial build up. Make a thick paste of baking soda and water. Coat all burners with paste and let stand for 20 minutes. Scrub with a sponge and rinse thoroughly. Make sure to remove the electrode when cleaning the burner. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Christopher Lotesto
February 5, 2020
My xl burner (mfg# 74007736) ignitor is clicking but not lighting...i see from other entries that i should replace the head/ignitor assembly but there is now also a faint smell of gas coming from center of the burner (no worries - turned it off at the valve) and i'm wondering if there is any advice regarding the gas "leaking out" as i don't think burner head replacement will solve that?
For model number Jenn-air JGD8430ADB
Hello Christopher, thank you for your question. If there is a small leak of gas that is usually caused by the burner valve that controls that burner. We would recommend replacing the burner valve as well as the head/igniter assembly. I hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Joyce
November 28, 2017
My Jenn-Air range right front burner sparks but doesn't ignite every time, sometimes get strong gas smell. It's a slide in 30" model, which part i need to purchase? Is that easy to replace myself? Thanks.
For model number JDS8860BDP
Hi Joyce,
Thank you for your question. I would suggest checking your burner electrode or the igniter right behind the knob on your stove. It sounds like either one of those two parts could be your issue. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Ron
January 20, 2018
What part number is the small, left front, burner head with electrode.
For model number JGD8430ADN
Hello Ron, Thank you for your inquiry. The left front burner head is part# WP7505P339-60, the electrode comes separately for this burner, part# WP74009336. Hope this helps!
Was this helpful?
Thank you for voting!
Bob
August 8, 2018
Will this part: Partselect number ps2085280
Manufacturer part number 74007736
manufactured by Whirlpool fit on the left front burner, which is the largest on the stove
For model number JGCP648ADP
Hello Bob, thank you for your question. Yes, this part X-Large Burner Head with Electrode 74007736 - is the largest burner on the unit and would fit that front left burner section. I hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Cooktop","title":"Cooktop","url":"/Cooktop-Parts.htm"},{"position":2,"name":"Element or Burner","title":"Element or Burner","url":"/Cooktop-Elements-and-Burners.htm"},{"position":3,"name":"74007736","title":"74007736","url":""}]
You added 1 item to your cart
✖
% OFF
$
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
