Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Phil
November 29, 2018
Is this burner head 4.25” in diameter?
For model number JGD3536WSO1
Hi Phil,
Thank you for your question. The diameter of this large burner head is approximately 3 1/2 inches. I hope this helps. Thank you and have a great day!
11 people found this helpful.
Was this helpful?
Thank you for voting!
Larry
November 14, 2018
All of the screws in the burner heads have seized in the assembly. I have soaked them for days without success, any suggestions?
For model number JGD8430ADB
Hello Larry, Thank you for the question. Most times in this case, they will need to be drilled out. Thank you for your inquiry, good luck with this repair!
4 people found this helpful.
Was this helpful?
Thank you for voting!
David
November 22, 2017
Does this part replace the medium burner and include the electrode?
For model number JGCP648ADP
Hi David,
Thank you for your inquiry. The burner head does not include the electrode. The part number for the electrode is PS11744318. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Bryan
February 19, 2018
Is it possible to change one the smaller burners to a larger size ?
For model number JGD8430ADS
Hi Bryan, Thank you for the question. We can only recommend using the size burners that came with the appliance. Hope this helps!
Was this helpful?
Thank you for voting!
Prema
July 4, 2019
The screws were rusted and the tops broke off, so i have to now drill the screw out, i guess. However the ignitor fell into the hole completely, so how do i replace it now?
Hi Prema, thank you for your question. You are going to have to open up the appliance and put the part back into place. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
Adam
January 7, 2020
This model has the screws that hold the burner tops in place, do you really need the screws if the heads break off but there is still s stub there that holds it in place?
For model number JGC8430BDS
Hello Adam, Thank you for the question. As long as the head is still secure and not lose, you should be fine. We hope this helps!
Was this helpful?
Thank you for voting!
Adam
January 7, 2020
Are all the ignitors supposed to spark when you lite just one burner?
For model number JGC8430BDS
Hello Adam, Thank you for the question. It is a typical for the gas stoves to spark all of the burners even when only one is needed. We hope this helps!
Was this helpful?
Thank you for voting!
Shawna
February 1, 2020
Need the replacement burner base for the burner # 3 btu 10000
For model number KCGD506GSS
Hello and thank you for writing.
Burner head # PS12070537 is in the list of compatible parts for your model. We hope this helps. Please contact us anytime if you require further assistance.
Hi, Question: igniters continue to fire after flame is present.
For model number JGC8536ADS
Hello Brian, Thank you for the question. If all burners are clicking, we suggest cleaning around the igniters to make sure there is no moisture or food debris. If they are clear make sure the burner caps are centered. If the clicking continues, you may have a defective Spark Module. This part sends enough current to the igniter to create a spark to the bottom of the burner cap. We hope this helps!
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
electrode would not lite burner
Unscrewed burner head and replaced with new burnerhead and electrode. Just like new. Parts cost 128.00 including shipping. Very simple repair. Saved 200.00 in labor. Parts came within 36 hours. Super Fast.
The igniiter is made of ceramic and had cracked. I remove the burner assembly, but couldn't remove the screw holding the igniter. After trying liquid wrench and every available screw driver. I opted to order the complete burner assembly. I installed the new assembly in 5 minutes and it worked great. This is the second ceramic igniter that has cracked on this stove top and both times I've had to replace the whole assembly. For a $1000 stovetop, I expected better quality. I'm just wondering how many times I'm going to have to replace burner assemblies. Each time it's been a different assembly.
Sidney from Saint Francisville, LA
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
8 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electrode not igniting burner
I've done this once before on this same gas stovetop as the electrode can degrade if it suffers from too many "boil-overs". The most important thing to do if the 2 screws holding the burner head on the cooktop are "tight" and don't unscrew easily is to soak them with WD-40 to loosen them up. Don't be in a hurry. They may need a couple of soak and waits. Once the screws are out, it's just a matter of connecting the wire on the electrode and replacing the burner. Also a Star screwdriver that fits properly is essential.
Thomas from Cary, NC
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
8 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two burners click, but do not light
I had the front right burner and back left burner always click, but never light without help from a match or lighter. So I saw how you can use rubbing alcohol to clean the ignitors with a Q-Tip. I did that, but the ceramic on the back left ignitor broke off with just a gentle cleaning. I ordered a replacement ignitor which came quickly. While waiting I had to try to get off the burner, as the Torx (star) screws were both not budging even with a little WD40. I ended up drilling both screws out. When the ignitor came I replaced it quite easily. However, all five burners started clicking and kept on clicking once I plugged the cooktop back in. Problem number two - the Spark Module or wiring had a problem. It was the Spark Module and I'll describe that repair with the next installation s=instruction I fill out.
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
