This stainless burner knob is used in ranges and ovens. The knob allows you to adjust the heat of the surface burner on your range. This knob accepts a D-shaped shaft. If your touchpad does not respond, the knob does not rotate, gets stuck, or the gas igniter glows but does not light, changing out this part can solve your problem. No tool...Read mores are needed for this easy replacement. Make sure to unplug your range from the power source before installing. Refer to the manual provided by the manufacturer for further guidance.
This is a burner electrode for your oven, range, or stove. This part has a male spade. It helps your burner ignite by creating a spark, producing a flame, and lighting the surface burner. If your burner will not heat properly, you may have to replace the burner electrode. Your electrode is located under your burner. This is an OEM replace...Read morement part that will be sourced from the genuine manufacturer. This part measures less than 1.5 inches long. It is sold individually. If you need a wire lead to complete your repair, you can purchase them locally.
This is the burner head and electrode for your gas range. If your gas igniter glows but will not light, or if the element will not start or heat entirely, you may need to replace the burner head. This burner head is approximately 4¼ inches in diameter and is sold individually. Please note that the mounting screws for this burner head are ...Read moresold separately. To replace the burner head, simply unscrew the old, defective burner head and screw in the new one.
This burner assembly is designed for a small burner on a gas range or cooktop and includes the burner head and spark electrode. The burner head directs gas through precision openings to create a steady, controllable flame, while the electrode ignites the gas for reliable operation. A worn or damaged assembly can cause issues such as weak ...Read moreflames, uneven heating, or failure to ignite. Replacing this part restores proper burner performance and ensures safe, efficient cooking. Installation is straightforward—remove the old assembly and secure the new one using existing hardware.
This part is the replacement grommet for your cooktop or range. It is made of black plastic and is approximately 1 ¼ inches in diameter. This part may also be known as the cooktop burner knob gasket, and it creates a seal between the burner knob and the control panel. The main reason to replace the gasket is if it no longer creates a seal...Read more, or if it is otherwise broken, damaged, or missing. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Randall - For model number JGC8536ADS
June 4, 2026
I need to convert back to LNG from propane. Need to orifice’s. Please help
Thanks!!
Hello Randall, thank you for contacting us. You will need the following orifices to convert the cooktop back to natural gas: Center orifice is part number PS11744608, Left Rear is part number PS11744606, Right Front is part number PS11744607, Left Front and Right Rear is part number PS2086969 (2 needed). The orifices are not available as individual parts, they come with the orifice holders assembly. Glad to be of assistance!
When I turn on the burner the igniter lights the burner but keeps on sparking the whole time the burner is lit
Hi James, I would make sure the burner cap is in alignment, you can also try and clean debris out of the grooves of the igniter. Otherwise you may need to replace the igniter itself. Thank you for your question and good luck with your repair!
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Michael West - For model number JGC8536ADS
February 19, 2020
I am trying to remove the large head on the burner to replace the igniter there are (2) two small torx screws i removed and i can’t get the head off the cooktop. I’m not sure how the head is connected to the the surface (is it sealed or am i missing something?)
Hello Michael, thank you for your question. The head should simply lift up off the top when the screws are removed. It sits on the orifice and tube holder. If the head will not come up, try some solution around the head to loosen it. I hope this helps.
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Bill - For model number JGC8536ADS
February 23, 2022
The 2 screws on each of the burner heads I'm guessing is how you get the top of this cooktop off. Mine will not move and I think I will break the screw if I try much harder. I have tried penetrant to no avail. Is this cooktop still available and what is the price.
Hello Bill, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11738715. All prices are shown on the site. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Hello Terri, thank you for your question. This usually means that one of your spark switches is shorting out. The Spark Ignition Switch on the Left side is PS11744199. The Spark Ignition Switch on the Right side is PS11744201. We hope this helps.
found the picture of the piece I needed on your website, ordered it and have it almost immediately. very pleased with the service.
Was this helpful?
Thank you for voting!
continually having to replace the knobs because they are made of cheap plastic and split down the side for whatever reason I don't know. I do not know what I am doing to cause them to split down a side. Why can't they be made of a heavier metal?
212 of 366 peoplefound this instruction helpful.
Janet from Chula Vista, CA
Really Easy
Less than 15 mins
took old one off with fingers replace with new one with a new knob again
My Orders
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for Jenn-Air Cooktop")
