This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
NOTE: Per Manufacture, belt measures 48.22" long uninstalled and the belt will stretch To 51.53" when installed.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Kenmore Washer Drive Belt
Troubleshooting
This part fixes the following symptoms:
Will not agitate | Burning smell | Spins slowly | Will Not Start
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Donald D - March 28, 2023
Verified Purchase
Drive belt
Fit and works great
★★★★★
★★★★★
Terry K - February 24, 2022
Verified Purchase
Repair was straight forward. Belt broke in a few weeks
Dealing with this company was easy and the belt came in a reasonable time. However, the belt actually just broke in half 2 days ago just a few weeks after installing it. The original belt made it 13 years and had simply slipped off, it did not break. I bought the new belt as I figured the old belt may have stretched out that cause it to slip. I now have reinstalled the old belt to get by until I figure out what to do about the broken belt.
March 2, 2022
Thank you for your review. I’m sorry to hear that happened, we will be in touch soon to help fix this issue.
★★★★★
★★★★★
Leslie L - January 20, 2022
Verified Purchase
Great!
We are so thankful for Partselect.com they carry all the parts we needed to keep our 2003 Whirlpool Duet set running for many more years to come! The part fit and worked perfectly!
★★★★★
★★★★★
Tina O - July 18, 2021
Verified Purchase
Belt was big enough.
It took some time and first buying a belt too small, but then I found this larger belt. It took about 30 minutes to get it put on, but it worked! Very happy! T.O.
★★★★★
★★★★★
Dean D - March 10, 2021
Verified Purchase
Hard to put on....an easy way to do it.
Exactly the right belt the first time. The belt seemed to small to fit on the first try. But I use a clamp (vice grip pliers) to hold the belt from slipping on the drum pulley and then turned the drum pulley until the belt was fully on the pulley.
★★★★★
★★★★★
Danny M - November 20, 2020
Verified Purchase
Watch you fingers
Excellent belt. Was amazed at how stretched out the old belt was. New belt is working great! But...watch your fingers when putting it on! Lol It's easy to get your fingers pinched when installing it.
★★★★★
★★★★★
Scott S - May 7, 2020
Verified Purchase
Perfect fit!
Went on easy and washer works great!
★★★★★
★★★★★
Gary B - January 1, 2020
Verified Purchase
Washer Repair Drive Belt
Part came quickly and fits and works as advertised.!
★★★★★
★★★★★
PHILLIP M - May 28, 2019
Verified Purchase
easy repair
the belt fit perfect
★★★★★
★★★★★
Sharon M - February 25, 2019
Verified Purchase
Easy repair
the part fit perfectly..realized how much our belt had stretched over the years..your video directions was right on..now my washer spins like new. will be ordering from here again..
Thank you.
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 5 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
tub would not turn
take the back cover off and put belt on. the belt is a tight fit and requires sone effort, but can be done.
claude van from big sandy, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drum didn't turn/spin
1) Removed back of washer 2) Removed nut holding pulley 3) Pulled pulley off shaft 4) Put new pulley on shaft 5) Replaced and tightened nut 6) Replaced belt on pulley 7) Replaced back panel 7) Washed pile of laundry
I first removed the back panel held on by about 10 screws. I removed the drive belt from the pulley, then removed the lock nut securing the pulley to the drum & removed the pulley. Attached the new pulley to the drum, tightened on the lock nut, attached the new belt & ran a spin cycle. When that went OK I replaced the back panel & the
... Read morewasher was back in service.
I first had to take off the back and the top to get to the pulley and the belt. The pulley had woobled so much that it had worn out the center nad it would no longer hold to the post in the tub. It also had cut into the back of the tub about a 1/4 to 1/2 inch. I unscrewed the nut holding the pulley and removed it. I then took a knife and
... Read more trimmed the rough edges off the back of the tub to make it smooth. I then smoothed out the end of the post that the pulley fits on so the new pulley would fit. I tightned the nut and put the belt on the motor drive shaft and Used a robo grip to hold the belt as I turned it onto the pulley. I but the back and top back on and that was it.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Manuel
October 5, 2017
My machine makes a loud of noise when it is spinning. Is this normal? It has done for a long time ( two years ) and nothing has broken yet. The machine had a previous owner. It was in the house when i bought it. Thanks for your answer.
For model number WFW9750WW01
Hi Manuel,
Thank you for your inquiry. There are some parts that you will need to check to see which one is causing the issue. You will need to check the drain pump, the drive belt, the drum drive pulley, the tub gasket, the shock absorbers, the springs, the driver motor and the dispenser actuator switch. I hope this helps. Thank you and have a great day!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Ansheng
November 23, 2019
I ordered belt it does measured as size of 48.22 inches. But it is too short for mount at poly wheel. I don't believe it can possible to expend to 53". I don't know how can solve this problem. Ansheng liu
For model number GHW9100LW
Hi Ansheng, it should expand to stretch to 51.53 inches when installed. If it is not expanding to this size there may be a problem with the part. Thank you for your question and good luck with your repair!
