Maytag/Maytag_Thumb/TCQNS8DN.gif
See part 2 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Bellow To Tub Clamp

★★★★★
★★★★★
3 Reviews

Rated by 3 customers 

A Bit Difficult 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your 11041932510!
 Fits your 11041932510!
PartSelect Number PS11746259
Manufacturer Part Number WP8540108
Manufactured by Whirlpool
You May Also Need?
Product Description

Bellow To Tub Clamp Specifications

This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place on the washer frame. The main reason you would want to replace the bellow clamp is if it is rusted or damaged, and it is not holding the bellow in place. To remove the bellow clamp, simply use a screwdriver to pop the bellow clamp out of the groove it rests in. Place the new clamp back into the bellow groove until it snaps into place. This is an OEM part from the manufacturer.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Maytag, Whirlpool, Kenmore, Inglis.
Part# WP8540108 replaces these:
AP6013038, 8540108
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David
March 9, 2020
How do you put the bellow wire back in place it came out in the wash
Hi David, thank you for your question. We have an installation video for parts like that here: https://youtu.be/WD0W84vc91E. Good luck with your repair.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Customer Repair Stories
 Average Repair Rating: 2.3 / 5.0, 3 reviews. What's this?
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
leaking at door
once i figure out how to take off front panel it went quite smoothly also my wife gave me a hand putting the bellows on,her fingers were smaller so it was alittle easier for her
Other Parts Used:
Front Load Washer Bellow - Gray
  • william from wauseon, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
22 of 46 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Torn tub seal causing major water leak.
Removed top of washer. Removed top front panel. Removed old front panel clamp. Removed front door panel. Removed old tub clamp. Then removed torn tub seal. Installed new tub seal. Needed two sets of hands to install new tub seal. Pretty tight installing the new tub seal around drum lip. Might be a good idea to heat up or let your new tub seal soak in water prior to installation. Once tub seal was installed, I installed new tub clamp then re-installed the door switch. After that, I put the front door panel back on. Then tightened down the door switch. Finally, I installed the top front panel and then the top of the washer.
Other Parts Used:
Bellow To Front Panel Clamp
  • Matthew from MENTOR, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking
Followed the video except to use clamps to hold the Bellow To Front Panel Clamp in place while I worked the clamp around the from of the Bellow. I used a plastic pry tool in place of the suggested screw driver to pry the control panel off.
Other Parts Used:
Bellow To Front Panel Clamp Front Load Washer Bellow - Gray
  • Linda from S SAN FRAN, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
3.3
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11746259
Manufacturer Part Number: WP8540108
Brand
Model Number
Description
Kenmore
11041932510
Washer - COMMERCIAL WASHER
Kenmore
11041942710
Washer - WASHER
Kenmore
11046462500
Washer
Kenmore
11046462501
Washer
Kenmore
11046472500
Washer
Kenmore
11046472501
Washer
Kenmore
11047511700
Washer
Kenmore
11047511701
Washer
Kenmore
11047511702
Washer
Kenmore
11047512600
Washer
Kenmore
11047512601
Washer
Kenmore
11047512602
Washer
Kenmore
11047512603
Washer
Kenmore
11047512604
Washer
Kenmore
11047512605
Washer
Kenmore
11047531700
Washer
Kenmore
11047531701
Washer
Kenmore
11047531702
Washer
Kenmore
11047532600
Washer
Kenmore
11047532601
Washer
Kenmore
11047532602
Washer
Kenmore
11047532603
Washer
Kenmore
11047532604
Washer
Kenmore
11047532605
Washer
Kenmore
11047542600
Washer
Kenmore
11047542601
Washer
Kenmore
11047542602
Washer
Kenmore
11047542603
Washer
Kenmore
11047542604
Washer
Kenmore
11047542605
Washer

Get in touch, we're here to help!

Open until 1am EST

Contact Customer Service