This tub to pump hose is thirteen and a half inches long. It is all black in color and is made of plastic.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Maytag Washer Tub to Drain Pump Hose
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer.
This part works with the following products:
Maytag.
Part# WP22003285 replaces these:
AP6006353, 22003285
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
5.0
Filter By Rating:
5 Stars
3
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Jeff H - March 31, 2021
Verified Purchase
Exact fit.
As good if not better than original.
★★★★★
★★★★★
James D - June 11, 2019
Verified Purchase
Great service
Got the exact part I ordered. Could not have been better service.
★★★★★
★★★★★
Marie W - August 10, 2018
Verified Purchase
Great website
The part was exactly what I wanted to ordered. Easy model # look up on your website, fast delivery.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 6 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Washer Was Leaking When Water Was Pumping Out
Took a putty knife and raised the top,then took two bolts out, then pulled front panel off. Took hose off from the tub to the pump,and put the new one on. It's working fine.
JERRY from LEXINGTON, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water leak
pop top,remove 2 screws,remove front panel.remove 2 spring clamps from tub hose.reverse!
william from norristown, PA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
4 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water in the floor
take a butter knife and pop the clips loose on the front between the lid and the front take the two screws loose on the front in each corner remove the front cover and you will see the hose take the clamps off and replace the hose
Huston from columbiana, AL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking under washer. Tub to pump hose sprung a leak.
There are two clips that hold the top of the washer down. Releasing these clips allows you to lift the top; it is hinged at the back. Then remove two screws holding the front panel and remove the front panel. The tub to pump hose is easily accessible. It is held in place by a hose clamp at each end. Use pliers to squeeze the clamps and re
... Read moremove the hose. Replace with new hose. I re-used the original clamps.
Read less
Richard from Cedar Park, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
13 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water on the floor
figured out how to open the top of the washer(Two small tabs I pushed in with a putty knife. Looked for the area it was leaking. Slide the hose clamps off with a pliers and pull out hose.
Put clamps on new hose, replace hose and slide clamps to ends to seal the connections
Russell from Aplington, IA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking pump hose
I thought I was going to need to replace the leaking washer machine. Water was every where and after checking the main sewer drain was ok I lifted the washer and found the water pouring out the bottom when i put it on. After finding out how to get the whole top open and the front panel off I was able to locate the source of the water
... Read more leak on my washer machine. The cause was split in the plastic hose that goes from the tub to the pump. After the new hose arived I was able to replace it within 10 minutes. So far so good. Thank you Part Select.
Read less
Brian from Lynbrook, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
23 of 28 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.