YKHMS2040WS0 KitchenAid Microwave - Instructions

I first unplugged the microwave. I then unscrewed the 2 screws from the top grill. I had to be careful because the grill was cracked close to each screw. It was a little tricky to remove the grill. Had to tilt it down as I removed it, and make sure the microwave door was opened as wide as possible. Filters were placed as the old ones, with the metal part up I believe. A little tricky to get one of the filters to fit. Grill was replaced with care so as not to further Crack it. Kind of maneuvered grill back in place, getting right side in place first. I noticed there were several tabs on the grill that needed to be placed inside of the microwave body while reinstalling the grill. Once the grill was in place, the 2 screws were put in to hold the grill in place.

Remove “over the stove” unit. Remove unit shell case. Unscrew and disconnect diode. Replace diode. Re-assemble. Put unit back in place.

Replaced broken glass tray. Used two screwdriver to remove top front panel to replace charcoal filter. Microwave parts diagram with descriptions and part numbers made the project very simple. Price of parts was substantially less than manufacturers price schedule. A very satisfied customer.

Really easy for a 75-year old female; just spent more time reading the online manual than actually installing the light bulbs to find out where to access the light bulbs.

mounted bracket, case closed.

Don't waste your time with other parts stores online. Partselect sells quality parts and they arrived 2 days early. I purchase a door switch from another online store and the switch was defective.

Removal of Phillip Head screws from Top vent and Control panel. Removed Torx head screw to remove entire switch assembly. Removed three wires to switch leads. Unclipped old switch. Replaced wires and inserted New switch in to clips. Attached assembly with Torx screw. Set Control panel back into place and screwed in top screw. Replaced upper vent with 2 screws.

Simply removed old screws from the remaining pieces still attached to my microwave. Cleaned up all surfaces. Put new grille into place. Replaced screws in the holes. Went great. Part fits perfectly.

This should be a 1 minute repair. However, there are a few issues. First, make sure you order the correct bulb. Mine is a halogen push in bulb, but the parts list showed a screw in bulb.
Remove power from the unit OR be sure that the light is turned off with the push switch.. The display will show the status as you rotate through the dim levels.
There is a single Phillips head screw holding the cover on the underside of the over stove microwave. carefully remove it. When loose the panel will drop down and you will find the old bulb in the center of the front of the opening. Remove the bulb. Now the important part. Carefully unpack the new bulb being careful to not touch the glass with your bare hands or fingers. Then insert the bulb into the socket.
If you unplugged the unit then plug it back in and push the switch to check that the new bulb works and is in the socket, then turn it back off.
Carefully lift the cover back into position and replace the screw. This is the hard part as you are working upside down and can't really see when it is lined up properly. When you have the screw back in and tight you are done. Press the light switch to enjoy your lit up stove again and put your tools away.
If you get your fingers on the glass bulb then clean it off with some rubbing alcohol and a paper towel to remove any finger oils before you put the cover back in place. Finger oils can boil with the heat of the lit bulb and cause the glass to explode. This holds true for any halogen bulb.

Part of the support was missing. I had to remove the two switches and put them in the new bracket
Had the switches reversed and started blowing fuses. Reversed them and changed the fuse and it started working.

We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.

Turn off power supply at breaker . Replace old bulb with new bulb .

I removed the broken tray and ring-turn and replaced it with the new
Service was fantastic, parts were ordered one day and received the next

screwed in new bulb

Washed the glass tray and put in the microwave oven. Easy..