Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Detergent cup opens only half way.
First, let me say that the parts arrived really fast,--thnaks for the great service!
First I removed the screws inside the door edges. This releases the front door panels allowing access to the detergent cup parts. Then I removed the old cam return spring, the old cam (and the old spring underneath the cam) and the old bi-metal switch. The instructions were pretty clear on how to install the new style return spring and new cam. Then I installed the new bi-metal switch.
Really, the hardest part of the whole repair is getting the door panels back in the proper place so that the screw holes are aligned. That probably took longer than the rest of the repair job.
The new parts have the detergent cup working like new again. Very satisfying repair!
I removed front bottom cover,found belt broken. I ordered part online on 10-23-09,part arrived on 10-24-09,amazing. I lossened the two bolts that hold the drive motor to the frame,slipped the new belt on and applied the supplied silicone grease. I then ran the two bolts in with a 3/8 wrench,put the cover back on. Everything works like new now. Great delivery and easy ordering system online. Immediatly called my neighbor and told him about partselect.com
1. Removed the four screws to remove the door front. 2. Removed the six screws to remove the detergent cup. 3. Replaced bimetal strip, cam, and spring. (simple task) 4. Replaced gasket and seal. 5. Replaced detergent cup. 6. Replaced door front.
The detergent holder wouldn't spring open during the wash cycle
First, I had to remove the outer face panel of the door. Four screws on the inside of the door hold the large panel onto the front. Removing these screws and the panel revealed the detergent cup assembly. There is no need to disconnect the power as long as the door latch is in the open position for this repair. I removed the two wires, blue and white from the leads, keeping note which was attached to which lead. I used a hex head screw driver to remove the 6 screws that hold the detergent cup in place. After removing the detergent cup and gasket, I cleaned the surfaces with a scouring pad to make sure the new gasket would have a good seal. I installed the new detergent cup with the 6 hex screws and re-attached the leads. I replaced the face panel with the four interior screws after running a couple cycles to be sure the problem was fixed, which it was.
The detergent cup would not dispense during wash cylce
Typically when the detergent is not being despensed during the wash cycle, the bi-metal switch is bad (they don't tend to last forever). I took the 4 lower screws out from the inside of the dishwasher door,, unscrewed the bi-metal switch, and screwed in the new switch. I also decided to replace the metal spring for the dish as well, which took the majority of the time. Once you get the idea of how that spring is wound in there, the install goes pretty quickly.
Took off bottom cover. Put belt on center housing than put belt on moter pully.Rolled belt down onto center pully while turning pully clockwise. Popped right on.
It was my first dishwasher belt and it was much tighter than I thought it was going to be. I was worried I was going to break it putting it on so I was a bit stumped, but finally got it on and its good as new.
The water inlet valve would not allow enough water to run effectively. To R & R the part only a phillips screwdriver, a smaller adjustable wrench and pliers are needed. Turn the water supply off, & disconnect the water supply. Remove 2 screws attached to the cabinet and remove the rubber fill hose with pliers to open the clamp. Remove the inlet fitting from the old part and place on the new valve, using teflon tape. Attach the new part to the cabinet wall then the water supply to the old, reused fitting (also with teflon). Obviously, turn power off and disconnect the 2 double leads before beginning and replace when done. A fairly simple job , and my miraculous Maytag keeps on going!!
Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!