Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher was leaking caused by a cracked brass nut attaching to the heating element.
First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.
Put spring in plastic bushing, snapped into door arm and hooked opposite end of spring in first hole. Repeated process on opposite side of door. Did the above without moving the dishwasher from installed position.
On my maytag portable dishwasher I had to remove three side screws on right lower panel,and two lower screws to free up panel. I had to pry the panel away from the body to get axes to the springs. Replaced springs as instructed reinstalled all hardware, finished.
DIshes not getting clean. Cover of detergent cup sticking half way.
After nearly 20 years of use (and no service) my Maytag dishwasher stopped getting dishes clean. I called Maytag and they made me an appointment with a nearby service center. The Maytag person also suggested I do a run with an open container in the dishwasher filled with a couple of cups of white vinegar – since that dissolves the white scale buildup from hard water. That helped a lot. Yay Maytag!
I had 5 days to wait for service, so I started Googling. I found very negative reviews of my local service center, but I also learned that I could buy a replacement detergent dispenser online and I found excellent simple instructions for installing it. It arrived in two days and I installed it. The hardest part was removing the front panel of the dishwasher to get access and supporting it while taking out the last couple of screws – then holding it in place afterwards while putting the screws back in. I recommend having a second pair of hands!
I also realized that the two rotating spray arms (at the bottom and at the top) weren’t rotating! They’re easy to remove (just unscrew the center component), and I found that many of the holes were clogged – including all the ones pointing sideways that make them spin. I had to force water inwards through the holes to dislodge the debris, then I filled the arms with water through the center hole and sloshed it around to clear things out. That worked. I put it back together – and the dishwasher is now as good as new!
For good measure I took the cover off the strainer in the bottom to clean it, but surprisingly the strainer was almost completely clean.
I cancelled the service appointment, of course. I’m sure I saved a lot of $$$.
I had read that recently mandated reformulation of dishwasher detergent with lower phosphate content makes it less effective – but I’m not seeing that: a little simple maintenance and my dishes are 100% squeaky clean again!
Belt seemed too small at first to fit, but turning the power module pulley while holding the belt enabled it to slip in properly. Didn't help that there's not much space to work.
I opened the door and pulled the old gasket out using a flathead screwdriver to pry up the difficult to remove areas. I cleaned the area with a damp cloth and place the new gasket in the slots. The entire process including the cleaning took no more than 10 minutes. It was so easy. By the way, I had the part in my hands 2 days after ordering it. I am very impressed with the service.
I removed access panle then disconected the wires, water inlet line, and water outlet line from the valve. then took the two screws that held the valve in place off and removed the old valve and replaced with the new. Its that easy. I had one problem that did'nt want to stop haunting me...water leaks at the conections. Tip: don't put access panle on untill sure there are no leaks. You might notice I had an earlier article with a float switch. It turns out that that was not the problem. This water valve was, and it works great again. Not bad for 24yrs old(yes, the dishwasher).
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wheels break or bend or fall off
if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.
The Retaining Nut of my Upper Spray Arm fell off and was stripped. I was thinking I was going to have to get a new dishwasher because mine is pretty old. I found Partselect.com and plugged in my model number and it gave me all the parts. It cost me less than $10 with shipping and it saved me about $450.
First I was amazed that the belt was available for my ancient dishwasher. Then I was amazed again when it came overnight. The instructions said to stretch it over the two pulleys but my hands weren't strong enough. In a sudden flash of brilliance I decided to use a screwdriver as a lever to force it onto the second pulley. Done deal - happy home handyman.
Remove the lower panel by taking out the 2 screws on top and 2 at the bottom of the panel. To diagnose the problem, verify that there is water supplied from the valve under the sink to the water supply valve under the DW. This can be done by turning off the valve under the sink, disconnecting the copper supply line under the DW then turning on the valve under the sink to see if water passes through the line.
The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.
Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.
Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops