WTW7600XW0 Whirlpool Washer - Instructions

two small compression clamps hold the hoses in place. these are very simple to remove, however to reinstall the new hoses you should unscrew the pumps with a nut driver, secure the hoses with the clamps, and then screw the pump back to the bottom of the drum. oh yeah make sure to put the back plate back on the machine

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

First replaced four basket spring supports. Next tried Basket hub assembly ( which showed wear, but not total solution). Next replaced the rotation sensor that's on the stator. That finalized the issue.

3rd time replacing this part. The plastic grooves against the metal get wore down. Only 20$ to repair ! Take off the 3/8 bolt - center pops out. Remove screws pop out old piece and tighten new piece each side evenly.

My problem stemmed from a previous leaky bleach dispenser hose (repaired over a year ago). It had leaked just above suspension rod assembly (only 1 of 4 was effected).Rod had rusted to point where it snapped just below the top mount. This actually made the replacement very easy as the rod simply slid out of the bottom tub channel and onto floor when washer tilted 45 degrees. Before tilting washer, unplug washer and disconnect supply lines and drain hos Use pry bar to separate cabinet top from cabinet lower section. Tilt top section to grant accesses to top suspension rod retainer mounts. Remove black rubber retainer washer from new suspension rod. As assistant holds tilted washer, a new suspension rod can be pushed thru bottom tub channel. Place black rubber washer back onto suspension rod. This will prevent the new rod from sliding full back out tub channel when released. The purchased suspension item has four rods and four top retainers. I could have reused the old retainer, but would have been more difficult to release the remaining rusted rod bit. So pulling up on rod and twisting suspension rod such that rod hook end pass thru top cabinet retainer cup and slides into position on new rod hook end retainer. Release retainer and rod, and move tub side to side allowing retain to assume natural position. (reference the other 3 retainers). Realign mating surfaces of cabinet top and cabinet lower if needed. Close cabinet top onto cabinet lower. Connect supply lines and drain hose, Plug unit in. Repair complete.

Removed the center cover of the agitator with a flathead. Removed the nut of the agitator main cover. Had trouble taking the cover off because of the crud holding it down I wiggled it up gently alternating n,s and e,w until I eventually saw it separating from the bottom of the basket. Once it came off you could see how nasty the old hub assembly looked. Took the screws off the old hub assembly and removed it. Matched it up with the correct new hub assembly cause the kit comes with 2. Cleaned the shaft and that general area. Installed the new hub assembly, replaced the covers. Ran the drain and spin cycle and it worked with no problem. There are videos on YouTube that show you too. DO NOT try to pry the agitator cover if it won’t rise up easily. Be patient and it will come out.

Replaced water inlet valve. Parts select video was incorrect for my unit. There are no spring clips to be released using a putty knife. Rather remove the two screws in the back of the top, pull the top forward and up to get at hose connections to the valve. Hint, place a towel under the valve connections because after removed from the valve, the hoses will leak to the floor. I propped the top up with a stick. All the other stuff in the video is good. Unplug and turn water off, remove connectors from old valve etc. . I also removed the protective plate over the cabled that runs between the washer and the control panel located on the back of the washer. The will make the sliding of the top forward easier. Only one screw involved.

Pretty easy! Just follow this link on how to fix the problem:

https://www.youtube.com/watch?v=_-Hg8rLGiKQ

The hardest part on fixing this is trying to move the washer out of its place so I can tilt it to see underneath the washer where the repair would be.

Removed agitator and basket hub parts and cleaned all parts of agitator then replace basket hub with new basket hub kit according to video ran washer but did not solve problem

Turn off and unscrew hot -cold hoses and drain line. Unplug power and pull unit away from wall. Tip onto front of machine and lean it onto something that will give you enough room to work as the pump is on bottom left back of unit. Unscrew all back plate screw's and remove back panel and keep screw's handy. Three main screw's hold pump in place but loosen hose clamp's first and its out. Reverse what you just did and you should be good to go! Good Luck!!

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

The inlet/diverter valve relacement steps:
1. Turn off electric and water supply and disconnect hoses
2. Remove hold down screws on back of control console
-Remove console to access valve and remove valve hold down screws
3. Label and disconnect valve connections
4. Insert putty knife 3 in. from each front edge to release hold down clips for top panel.
5. Disconnect hoses from valve assembly.
6. Remove old valve and install new.

Removed the old hoses and screwed on the new hoses.

Repair was pretty straight forward with the exception of removing the agitator. Hint, do not force it, just continue to work it until it releases. Problem was not entirely corrected, but improved.

Getting to the actual hub is a bit difficult as it involves removing the accetuator and takes some time and patience, but when I tried to replace with a new hub, I found that the screws were stripped, so PartSelect walked me through the ordering process and helped me choose the exact size screws that I needed. Parts came quickly...I already had the hub waiting to be secured and the screws tightened easily. (We had tried using a similar size, but you REALLY need the whirlpool screws that go in there) No more spinning problems, and the machine is not jumping around anymore. Works just like before. This particular machine has to have this part replaced at least twice a year (luckily it's cheap),but saves us from having to buy a whole new machine. My son also told me that since I replace the part so often, best to replace the screws every other time as well.