UKI1500AXX Maytag Ice Maker - Instructions

I have a Maytag Refridgerator with lower freezer and ice maker. Stopped making ice. Noticed the unit would fill up and freeze but the tray wouldn't rotate to drop the cubes into the tray. Cleared the frozen trays to see if it was just stuck but same thing happened. Replaced unit, not difficult with the exception that the top tray is ridiculously hard to get out. Never did do it, just worked around it. Working perfect now.

ordered a new shut-off valve. arrived in 5 days. installation had to wait a couple more day for i had to order a new compression nut. the reason i had to order a new nut was because the original nut was made of teflon and stripped easily when i tightened it to make a leak proof.joint. the new nut arrived in two days and was installed readily being that it was made of brass and consequently did not strip when i tightened to make a drip proof joint. finished in approximately twenty minutes' the video that this site has on the internet was of great value.

I removed the old icemaker, took it out to my shop & removed the wiring and etc. and put it back in place.

I read the instructions from your site, removed the old unit, salvaged the parts to be reused and reassembled. 1/2 hour later I had ice and no leaks.

very easy, 3 screws,took old one out, take 2 inter screws out (of ice maker) of old unit to replace water feed cup on new unit very easy,installed had ice after 12 hrs.

I first loosened the hex screws and lifted the unit off. Then I unplugged old unit from the wiring harness. I did have to switch the inlet funnel since the new unit was a little different. I used the one from the old unit. I then plugged it back in, rehung and tightened the screws. The unit started operating within a few hours.

I simply removed the 3 screws holding the unit into the freezer with a nutdriver, then disconnected the power plug (a little hard to get to, and requires releasing a small tab in a hole in the main body). The icemaker came right out with no problem. I then had to change out the water funnel inlet because mine had a different style than the one provided on the new one. This was easy also, just remove 2 phillips head screws that are set deep in 2 holes in the face of the motor drive unit, then pull the whole assembly apart far enough to allow the ejector blades to slip out of the hole through the inlet funnel, then snap the funnel loose to move it to the new one (the same technique to be used on the new one, then re-assemble in reverse order).

Unplug fridge, close off water supply valve. Remove two screws attaching assembly to freezer wall, detach wiring harness. Remove parts from old assembly: wiring harness, shut-off rod, harness clamp and attach to new assembly. Connect wiring harness, two screws attach new assembly to freezer wall. Plug in fridge and open water supply valve (after an opportunity to change in-line filter). Works now!

First i removed the three screws that held the assembly to the fridge, then removed the water flow tube from ice maker. 2- flipped ice maker over ,then used a small flathead to push in locking tab that held wire harness and out comes ice maker. All though the water cup was not quite the same i used the old ice maker to take apart to see how it was put together,hopeing there wasn't a myriad of parts. -NO INSTRUCTIONS- piece of cake, don't take out outside screws,take out the 2 inside screws-these srcews hold the guts to the water tray-pull apart and reassemble the unit after you have switched the cups. then reinstall into fridge with your outside cover and the full bin wire and your done. It helps to be alittle mechanicly inclined. -NO GUTS NO GLORY,DONT BE AFFRAID TO LOOK OUTSIDE THE BOX-

First, I removed the ice bucket. Then I removed the two top left screws and bottom screw with a 1/4 inch nutdriver. I pulled the assembly out as far as the wiring harness would allow, disconnected the harness on the lower left side, and removed the unit. I removed the old motor cover and ice stop wire and placed them on the new unit. I then reversed the process. It went so fast that the freezer must have still been close to zero degrees because it filled with water within 15 minutes.

Removed one screw ,unpluged ice maker, and replced it with new one.

Removed two screws on top. Then one under the ice maker ,held on to it while I unpluged the white flat plug. Then installed new one in reverse. Of course re-connect power wires on.
I turned power off at fuse box.
First batch of ice in an hour or so.

Barely a couple years old, was not getting any ice. I carefully selected the right part on this website and ordered. Around $150 and was easy install.

1. Mine was upper and lower freezer. you slide the freezer door out and lift it up, it will come right off.
2. pull out the tray above and ice bucket
3. Use a screwdriver to unscrew 2 screws above and one below the existing icemaker
4. unclip the power cable line

Thats it!

Point to note: the new piece you get will not have the power cable line, the water cover and the metal arm. I would think it should have for $150, but keep this as you will need a few little parts to complete the new part before installing it back.

VERY easy to do installation. Dont pay anyone to do this, it can be done easy!

First I removed the screw holding the ice maker on the wall and then loosen two other screws in oreder to remove the maker. Once out, I replaced the maker with the new one. Then replaced it in the refrig.

It was real easy. I unpluged the fridge. Took out the three screws that held the icemaker to the wall. Unpluged the wire harness. Removed the old icemaker and reversed the order to install the new one. Everything lined up perfectly.