Models > UKI1500AXX

UKI1500AXX Maytag Ice Maker - Overview

Sections of the UKI1500AXX

[Viewing 1 of 1]

Exact Part matches for your search term

[Viewing 1 of 1]
Add-On Ice Maker Kit – Part Number: UKI1500AXX
Add-On Ice Maker Kit
This part number matches the current model number UKI1500AXX
PartSelect #: PS1734740
Manufacturer #: UKI1500AXX
This kit is used with some top-mount refrigerators from 1997 to present. It includes the icemaker, bucket, water valve and other necessary parts for installation.
$151.63
  Special Order
Keep searches simple, eg. "belt" or "pump".
Replacement Ice Maker – Part Number: D7824706Q
Replacement Ice Maker
★★★★★
★★★★★
(136)
PartSelect #: PS2121513
Manufacturer #: D7824706Q
This ice maker (Ice Maker Assembly, Refrigerator Ice Maker) produces ice cubes that are ejected into the storage bucket. It is located in the freezer section of your appliance, mounted on the freezer ...
$132.70
  In Stock
Screw – Part Number: WP400021-1
Screw
★★★★★
★★★★★
(1)
PartSelect #: PS11742240
Manufacturer #: WP400021-1
Sold individually.
$12.96
  In Stock
Screw – Part Number: W11233072
Screw
★★★★★
★★★★★
(6)
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$19.99
  In Stock
Water Fill Cup and Bearing – Part Number: WP628356
Water Fill Cup and Bearing
★★★★★
★★★★★
(9)
PartSelect #: PS11743318
Manufacturer #: WP628356
This refrigerator ice maker fill cup dispenses the water into the ice cube mold during the fill cycle. Replacing the water fill cup is a possible solution if you notice that the ice maker is leaking, ...
$39.16
  In Stock
Single Outlet Water Valve – Part Number: WP61005273
Single Outlet Water Valve
★★★★★
★★★★★
(7)
PartSelect #: PS11743223
Manufacturer #: WP61005273
The single outlet water valve may also be known as the water inlet valve and is compatible with your refrigerator. This valve has a quarter-inch tubing inlet connection. When energized, this part rele...
$79.58
  In Stock
Cycling thermostat – Part Number: WP627985
Cycling thermostat
★★★★★
★★★★★
(1)
PartSelect #: PS11743313
Manufacturer #: WP627985
The ice maker thermostat, also known as the cycling thermostat, controls and regulates the ice maker ejection cycle by monitoring the temperature inside the freezer to determine when to release the ic...
$58.04
  In Stock
Compression Nut – Part Number: WP627018
Compression Nut
★★★★★
★★★★★
(1)
PartSelect #: PS11743305
Manufacturer #: WP627018
The compression nut is used as a connection between the water supply line and other components in your refrigerator such as your ice maker and your water dispenser. Tools required for this repair incl...
$13.04
  In Stock
Plastic Tubing – Part Number: WPB5705307
Plastic Tubing
★★★★★
★★★★★
(1)
PartSelect #: PS11747816
Manufacturer #: WPB5705307
This part supplies water to refrigerator components that require water, such as the ice maker and water dispenser. If you notice a leak coming from your refrigerator, the plastic tubing that feeds you...
$12.40
  In Stock
Screw – Part Number: WP681249
Screw
PartSelect #: PS11743743
Manufacturer #: WP681249
Sold individually.
$4.24
  In Stock
Ice Stripper – Part Number: WP2182124
Ice Stripper
★★★★★
★★★★★
(2)
PartSelect #: PS11739041
Manufacturer #: WP2182124
This is an authentic appliance part that is sourced directly from the genuine manufacturer. This ice stripper functions by stripping the ice maker mold of ice during the ejection cycle, after the wate...
$58.28
  In Stock

Questions And Answers for UKI1500AXX

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the UKI1500AXX

[Viewing 8 of 8]
Ice maker not making ice
Fixed by
these parts
Show All
Leaking
Fixed by
these parts
Show All
Ice maker won’t dispense ice
Fixed by
these parts
Show All
Ice maker dispenses too much ice
Fixed by
these parts
Show All
Ice maker dispenses too little ice
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Won’t start
Fixed by
these parts
Show All
Noisy
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment.
Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall.
Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer.
Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit.
Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable.
A good push of the new unit towards the snap-ins along with some upward force will get it stable.
Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in.
It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient.
Dump the first couple of batches of cubes just to make sure you're free of any residue.
Parts Used:
Replacement Ice Maker
  • Bernie from Diamond Bar, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
782 of 846 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water overflowed ice maker turnning ice bucket into solid mass of ice
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: one of the three screws that hold the ice maker to the refrigerator wall is hidden behind the large (black) end of the ice maker and is difficult to access. Before trying to replace the ice maker, make sure you have the physical dexterity to remove that screw. Second problem: it is not apparent how to remove the wire harness that plugs into the ice maker assembly. BEFORE you can remove the wire harness, you MUST remove the large white cap that covers the black end of the ice maker assembly and then push in a retaining tab to release the wire harness. If you don't do this, the wire harness will not release. Other than those two problems, it was relatively easy to remove three screws, unplug the wire harness, transfer three small, metal parts from the old ice maker to the new, plug in the new wire harness, mount the ice maker assembly so that the water tube is in the proper position, and then re-install the three screws. The ice maker works fine now. (P.S. I was told by an expert that the real problem might be a malfunctioning fill valve. I would have replaced the fill valve if replacing the ice maker assembly had not fixed the problem.)
Parts Used:
Replacement Ice Maker
  • Harry from Grand Ledge, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
263 of 347 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover which is snapped in place, then removing two recessed screws at the front. I removed the broken part, I then reassembled the ice maker with the new part. I replaced the two recessed screws at the front and snapped on the cover. Then I reinstalled the ice maker in the refrigator by plugging in the harness, slipping the ice maker over the loosened screws in the refrigerator and replacing the screw that was removed from the underside bracket. Tightening all the screws completed the project.
Parts Used:
Water Fill Cup and Bearing
  • David from Chester, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
103 of 125 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!