All Installation Instructions for Gaggenau Dishwasher SHUGGE1UC

Getting to the part at the bottom of the dishwasher was a little pain.

Everything went great installing the new drain pump. Our dishwasher works like it’s brand new again. I would recommend part select to anyone that needs to repair their dishwasher parts or any applications parts.

Parts Used:

Drain Pump

Travis from Hermon, NY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Missing/broken wheel on right side of lower dishwasher rack

I snapped the part in and voila!

Parts Used:

Lower Rack Wheel with Clip

Danette from SANTA FE, NM
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Lid for the streak treatment wouldn't stay shut.

Use screwdriver to gently wedge the side of the dispenser body apart enough to pop out the old kid, then insert the new kid in it's place.

Parts Used:

LID

Gary from NEW PARIS, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replace catch for door latch

Dishwasher door won’t stay closed. Upon inspection, the metal striker/catch at the top of the door was broken. This dishwasher is 12 years old and this is the first problem I’ve had with it. To repair the catch, first remove screws holding cover plate at the bottom of the door. Next, remove screws holding the dishwasher stable from under the counter. The pull out the dishwasher to gain access to the catch. You’ll have to take a small set of pliers and bend the two tabs back that hold the catch in place. Lift the catch up and forward to remove. Replace and bend the tabs back to hold the new catch securely. Move the dishwasher back in place and secure with the screws previously removed. Put the cover plate back in place and you’re done.

Parts Used:

LATCH

Michael from WEBSTER, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

At power turn-on the dishwasher would start in immediately in the Power Scrub mode and could not be changed or stopped.

I just removed the lower panel according to the manual, but the easier way is to remove the upper control unit by lifting upward. The difficulty with removing the lower panel is that the heavy-duty plastic pieces at the door hinge area are prone to falling out while trying to reattach the heavy lower panel. Replacing the control unit was very easy. All of the connectors have small locks on the back sides. Spreading the plastic locks for the control unit itself lets it come right out. The new unit just snaps in. Just be sure each connector plug is seated and locked. It takes longer to describe it than to do it.

Parts Used:

Main Control Board

William from MURPHYS, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Not pumping out

Remove spray arm. Pullout. Micro filter big screen . Tork bolt cover and small pliers to grab check valve flapper.

Parts Used:

Micro Filter

Check Valve

Eric from ELVERSON, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Clogged, old filter- dirty dishes

Removed old filter and replaced with new filter. Easy.

Parts Used:

Micro Filter

David from PENN VALLEY, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Not getting water

shut off water, pull dishwasher out, took side insulation off, unhooked what was connected to the float switch and replaced the new with the old. Reconnected everything and put insulation back and wa-la , all done

Parts Used: