SHUGGE1UC ((06)) Gaggenau Dishwasher - Instructions

With the help of You Tube, this 50 year old Mom got the job done. Not that complicated if you watch the step by step instructions on the Appliance Pro video. My repairman and husband were both determined to just buy a new one but this 20 year old dishwashing genius was just in need of a little repair. Only need a screwdriver, and slightly confusing as wires hook on a little different on new pumps. I suggest watching video the whole way through and then playing it step by step as you do the repair. Worked great for me. Thanks.

I used a wet vac to remove the water from the dishwasher. remove cover and filter/strainer from bottom of dishwasher. remove screw which allows you to lift the plastic piece to access check valve. Original check valve looked like new , I installed new check valve re installed parts . Job done and issue resolved .

Went to on line video and followed it. The old gasket came right out and the new one fit right in. Started at the top middle and worked the gasket in on both sides to make sure it was evenly spaced.

To perform the repair, the door panel must be removed (8 Torx screws) and the door removed from the hinges in order to access the lower door seal. For this model Bosch and other similar models, the hinge springs must then be disengaged (safer) or kept from retracting. To disengage the springs requires removing the entire unit, disconnecting the water supply, and flipping it on its side to disengage the springs. I chose the latter, keeping the unit in place, holding the hinges with vice-grips on either side, then removing the door. This was not easy and caution is required. Either method is risky with a 20-year dishwasher.
The replacement part does not fit as well as the original (much sturdier) part, but appears to seal well for now. Repair videos on the internet are for different, newer models where disabling the hinges as described here is not required, making the repair much easier. Recommend looking carefully at your model/manual to determine if the difficulty of the repair is easy or hard.

Turn off power to unit!
-Remove kick panel,2 screws.
-remove water valve, 2 screws, 3 electrical connections, 1 hose clamp.
-Remove elbow from old valve and install on the new valve ( use teflon pipe tape)
-replace valve, hose & hose clamp, electrical connectors and water supply line.
Scew unit in place ,2 screws.
Check for leaks then replace kick panel, 2 screws.

There are two ways to do this repair: the "right" way and the hard way. I chose the hard way, as the right way involves disconnecting the dishwasher plumbing, removing the dishwasher from under the counter, taking all the outer panels off, and disabling the door springs. There are good YouTube videos on this. The hard way doesn't involve that -- but is not all that easy and I'm not sure I'd recommend it. The problem, in essence, is that to install the new seal there is now way to do it without taking the door off the machine and taking the door apart -- which requires that the springs be locked out, if not disabled.

I accomplished that part of it by opening the door, partially, undoing the two screws on each side which hold the hinges, taking the front panel off (piece of cake, with a Torx driver),slipping the door partly off the hinges, and then locking the hinges open with the pry bars.

There are an assortment of ways one could seriously damage either the door or one's self doing it that way -- the hinge springs are very powerful -- so I don't recommend my approach.

Vice grip door hinges. No need to disconnect, un hook hing springs. Works slick. Small vice grips. On hinges. Remove tore screws. Remove seal , and replace seal, reconnect door screws. Boom done.

REMOVED DISHWASHER FROM CABINET. DETACHED BASE FROM BODY OF THE DISHWASHER. INSTALLED NEW CORD, REATTACHED BASE TO BODY OF DISHWASHER AND REINSTALLED IN CABINET. OPINION: THIS IS A LENGTHY REPAIR AND UNNECESSARY ONE. THE CORD IS PART OF THE DOOR COUNTERWEIGHT AND SUBJECT TO TENSION EVERY TIME THE DOOR IS OPENED, AS WELL AS POTENTIAL CHAFFING DUE TO PROXIMITY TO VARIOUS METAL PARTS, AND VIBRATION. THE CORD SHOULD BE MADE OF STRONGER MATERIAL AND ARMORED OR ALLOWED MORE CLEARANCE. BOSCH SHOULD FIX TO LAST THE LIFE OF THE DISHWASHER.

To replace the part per se was simple. To put everything back in place was more difficult as I took the base of the dishwasher off and a lor of other parts in order to reach for the drain pump. The irony was, after I took appart the base I fount a clip on the internet showing how to do that job and that was a very simple thing, couple of screws to take off the toe plate and the interior liner of the door, to create good access to the drain pump. Really a job of 10 minutes at the max.

First of all, I quessed at what was causing the droning noise. It seemed that it started when the d.w. was draining. I looked at various sites to try and figure out what was causing the noise but they all wanted money up front before they would discuss the problem. I gambled that it was the drain pump figuring that, oh well at least it's a part I won't have to replace in the future. I got lucky, the noise stopped with the part I bought. The only issues were the wiring harnesss wasn't the same as in the video I used. Overall, your service was very good. The thing I'm disappointed with is the fact that my expensive Bosch d.w. had to be repaired.

Use a screwdriver flat blade to pry up one edge of closed lid. Put one side of lid into hinge and snapped other side into place. Very easy.

I have granite countertops and one of the hold down brackets broke to wood cabinet side mount. Easy and fast repair to remove old brackets, pull out dishwasher, and I replaced both brackets with new, and new wood screws. New installation looks better than original done 18 years ago. Very easy to do and saved a lot of money if I had an appliance repair company do it.

Followed the video on your site and it was an easy install with no more leakage.

Disconnected the water and power, pulled dishwasher out from under the counter, unscrewed the old inlet valve, disconnected hose from exit of inlet valve, noted the placement of the wires and disconnected them. Installed new inlet valve in reverse order and reinstalled dishwasher.

Everything went great installing the new drain pump. Our dishwasher works like it’s brand new again. I would recommend part select to anyone that needs to repair their dishwasher parts or any applications parts.