Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer was squealing ( Tennant Complaint)
Followed the video as my unit was exact model( Front Loader) Thank You for your quick ship to me here in Iowa as my repair was made in St. Louis. Parts came with in 2 days then drove to St. Louis with confidence. We purchased this set in 2003 and it is first repair on dryer. This in my rental unit. Thx
Blower wheel came apart from molded-in nut, was loose, was rubbing on housing wall, and was likelynot moving to much air. I read some troubled stories about separating the wheel nut from the motor shaft so bought a new motor and blower housing and install wall pretty easy. There are videos on the teardown process and does that long and not alot of parts to keep track of either. I have already done the felt drum liner and rear drum ball and belt so if it's older than 15 years and your going to take the dryer apart, replace all these parts and you will about have new dryer at half the cost of new.
I basically followed the video instructions on your website. Pretty simple but ran into an issue pre-threading the 3 self taping screws into the spindle bearing. The screws provided were blunt on the end and did not tap easily at all. I used the existing screws that were much more "sharp" and worked much better. Also, the new screws were Philips drive and due to the amount of torque trying to self tap nearly stripped them out. The old sharper screws were square drive which had a better bite. So basically, I used the old screws to self tap and then used the new screws for the final installation. It took a long time to clean all the lint out from the inside of the dryer. The motor was completely embedded with lint and animal hair. You may want to suggest that a good cleaning may be needed so bring a shop vac...and also something to carefully pick the lint balls out from around the motor armature and bearing area. Overall the video instructions were really a big help!
Dryer was very noisy, like a vibration,or bad bearing
First i replaced the drum bushing on the rear of the drum ,it was definitely bad but noise was still there Decided it was the blower assy , pulled the dryer out disconnected the power,took off the frt panel with the door, disconnected the wiring to motor remover motor and fan assy, most trouble i had was fan is on motor with reverse threads messed with removing fan until I figured out it was backwards after that removed old fan and housing installed new one ,put dryer back together,started it and only normal noises Good for another 5 years Chuck
Had a squelch/squeak coming from the rear of the unit
I looked up a YouTube video on my specific model. Found one that said “basic disassembly”. I watched that and had it apart and back together in no time. Very easy to take apart and put new parts back in it. Re-assembled and since the repair no squeaking.
Top hinge on clothes dryer separated, leaving door difficult to open/close
Ordered part from partselect.com. Part was back ordered; however they were very proactive in communicating status updates! When it arrived it was simply a matter of removing door using a philips screwdriver, installing the new hinge and presto - job complete! Kudos to partselect.com ??
I recently ordered parts for a gas dryer, Frigidaire GLGQ2152 ES3. When I received an igniter part number PS12585650 order number 14700077, the igniter was broken when I opened the box. I believe what happened is that the new metal bracket was wrapped in the bubble wrap along with the igniter. I called customer service and was setup to return the igniter which I did. Also, I ordered a second igniter. I receive the second one and it wasn't broken and the bracket was outside the bubble wrap during shipment.
As far as the installation of the "replacement" igniter into the gas dryer, I could not find instructions on how to install it. The received igniter is much different than the original. There was a small instruction sheet stating that the new igniter is different but can be installed using the new bracket that came with the igniter. But again there were no instructions on how to do this. It took me great effort to figure out how to do this.
The old igniter had to be removed by removing the old bracket assembly that the igniter was mounted on. The new igniter had to be installed onto the new bracket and then by sliding the new assembly under the old assembly, the screws were reinstalled. Although the holes where the original screws were to be screwed into were too small, they had to be drilled out. There was no hardware (screws) to install the "replacement" igniter onto the shipped bracket.
After much work, I finally got the new igniter installed (without breaking it) with the new bracket and the dryer is back in operation.
removed the old gasket with pliers (noting where the beginning/end of the gasket was) then installed new gasket in the exact location with very light pressure on each rubber insert point. Voila!!