S8757W1 Roper Range - Instructions

I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.

Removed and replaced motor. In the process of removing old motor, the blower wheel had to be unscrewed from the rear shaft of the motor, in order to remove the motor. In my case, the blower wheel had seized up on the rear shaft and could not be unscrewed. It had to be cut off and it also had to be replaced. The dryer now works fine. Tip: I watched an internet video (repairclinic.com)about the procedure before I started. Very helpful!

the plastic fan can be tricky to get off,hold the pully side of motor with an adjustable wrench and turn plastic nut on fan clockwise.mine busted and i had to order another fan but they are easy to put on. counter clockwise to put back on.(reverse treads)

Googled the symptoms the cure was replace the motor. There was a video done by parts select that made the process even easier. Had it done in about 25 minutes.

I raised the stove top, read the instructions to my son while he did the work, then I lowered the stove top, installed the burner, and it worked like magic.

I read several customer feedback articles to find one with problem similar to mine. After eliminating the thermal fuse, it was obvious my motor was bad. Watched the video and easily removed motor. Took motor to a repair shop and they confirmed it was bad. Replacement motor arrived in two days (yes...2 days). Unbelievable quick delivery. Easy to reinstall---only took about an hour. Hey, it would have cost $500-$600 to replace this dryer! Now I feel like I have a new dryer for $80!

My husband figured this would be an easy fix....until he realized the part he had turn to remove the motor was made of plastic and was basically welded to the fan, so needless to say, we are now also replacing the fan....once the fan was loose, it was very easy to put in the new motor and fan and reassemble the dryer...good luck and watch out for those plastic moving parts!

Repair was simple, minus pulling the drive motor shaft out of the back fan. The female end of the dryer fan was made of plastic, so the socket wrench cracked the plastic end. Other than that, the repair was simple and easy to do. Much better paying the $88 for a new motor vice paying $400 or more for a new dryer. Dryer has run like a champ since replacing.

i did not do the repair but when my friend finish it was great, this company is great.

One screw taken out, 2 wires switched, new part & screw put in. Burner like new!

I checked the motor to make sure it turned freely but it didn't so I knew it was bad, your online instructions made it so easy for me to make the motor replacement, if I ever need any appliance parts ever again .....you can bet I'm buying them from you. I purchased the motor for about 40% less then what it was retailed locally.

Cut power. Removed four attaching screws and raised stove top. Cut two wires of existing burner plug. Used existing plug to select correct plug configuration from parts in kit. Attached new plug and wires to wiring harness using connectors and heat-shrink tubing supplied with kit. Used hair dryer to shrink tubing on connectors. Closed up stove. Restored power. Burner now functional.

Removed the original burner element sockets and replaced with parts provided in kit. Instructions were simple and easy to follow, problem completely solved in 20 mins!

Unpluged power cord.removed top and front pannels(after disconnecting wiring to door switch.) Removed drive belt to drum,and removed drum. Checked and marked motor wiring before disconecting from motor.Removed motor,After unscrewing the blower from shaft.(Had to remove jumper wire from motor)Reinstalled the blower and secured the motor,reconect wires to motor.(rechecked wiring connections)Put back the drum,drive belt,and the front door pannel.(reconect door switch wiring)then the top pannel.Plug in the power cord and checked opertion.....WORK'S JUST FINE! I ordered the replacement motor on a sunday,and the new motor was setting on my kitchen table tueday afternoon when i got home. Great job" PARTSELECT."

Repair went well your video was a great help. The motor was hard to disconnect from the blower and fan side.The shaft that you hold with the adjustable plier was hard plastic type of material and wanted to keep slipping and the edges wanted to round off and not hold in the adjustable pliers. I had to use a small pipe wrench with teeth to break it loose. The only other problem was the ground screw in the new motor had an odd type of head on it and took a special type of nutdriver attachment to loosen it and attach the ground wire to the new motor.