RM280PXBQ2 Whirlpool Microwave Oven Combo - Instructions

grandson removed the two screws holding in the burned out unit and removed the two wires, installed them into the new unit and put the prongs into place. very easy and certainly very economic. delivery was quick and postage was reasonable. Thank you.

Simple. But beware changing just the bulb when the gasket is not secure.

Simply remove two screws on each side of the oven door. Remove what was left of the old handle and slide the new one in place. Replace the two screws on each side and it was done. Very impressed with the whole experience. I paid for standard 3 to 5 day shipping and received the parts I ordered less than 24 hours from the placing the order.

Watched a you tube video prior to installing new switch. Followed the video which gave me confidence i was up to the task. After removing the touch pad I found my design was not exactly like the you tube model but I found the defective switch, replaced it and put the microwave back together. Works great. Again watch the videos

Unscrewed plate and replaced new handle. Very simple repair. Whirlpool was pricey on the handle but PartSelect had no determination in that. I researched the pricing and they were right on track with it. Delivered it in just a couple of days and I was back in business. Would definitely purchase again. Hassle free, great service! Great website and easy to purchase from. Very detailed prints, when trying to figure out what you need. Not sure if I needed just the brackets or the entire handle but the prints showed came in handy and showed me what I needed. Thanks~

I had previously partially removed the element and tested with multi-meter to determine that it was not working (open circuit). Repair procedure follows:

Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.

The button fell apart, then fell out of the microwave. I found the part on the internet and print the page. Went to my local Sears to see if they had part in stock. Sears uses something just above a DOS base computer system. If you do not have the exact part number they can not help you-mind you the part itself does not have a number on it. Anyhow, I order the part which arrived in three days. Simply, put the old spings in place and snaped the piece in place.

Did require removing almost every screw in the oven door. Labeled the screws as they were removed. Not difficult, just like solving a puzzle.

As soon the Bake Element has arive, I install it no more than 5 min... All I nedd was a Screw driver. It was so easy, Thank You PartSelet!

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

I removed the back panel, unplugged the wires, removed the 2 screws, replaced the element, plugged the wires back in and put the back panel back on. Now that I'm thinking about it, I guess I didn't even need to remove the back panel to replace the element.

Naturally the oven turned was off but for added safety I also set the breaker protecting the oven to the off position. Where the element attaches to the oven there is a small plate with two screws holding the element in position. Remove these two screws and then gently pull the element out 2-3 inches, which will expose the electrical connection. Using needle nose pliers gently pull on one of the wires to remove it from the element. Now remove the other and discard the old element. Simply plug the new element into those wires and screw the plate back into the oven. Now turn the breaker back on and you're done. Super easy!

unscrewed two screws put in new element replaced two screws done, recieved the element within days of order,it was the right part,couldn't have been happier with the service from parts select thank you.

Just like you said,remove two screws,pull out element,disconnect wires,install new part. It was easier to pull out stove and hook up wires.

My husband is an over-the-road driver, so I have to do all of the repairs myself. I went to the breaker box and turned off the power to the range. Then I removed 2 screws, pulled the element out about 3", and disconnected the wires. I then connected the wires to the new element, pushed it back in place, and replaced the screws. We had Parmesan Chicken for dinner and my children were thrilled!