Models > RGB746HED3WH > Instructions

RGB746HED3WH Hotpoint Range - Instructions

All Instructions for the RGB746HED3WH
91 - 105 of 146
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
cosmetic look of the stove top
changed double burmer pans
Parts Used:
Double Burner Pan - Left Side Double Burner Pan - Right Side
  • Danuta from Oxnard, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burners would not light
Remove the old tubes. Lift the lid NO MORE THAN FOUR INCHES. !!!!! Feel for the connections on the switch ends and attach losely. Carefully ( with some slight bending ) attach tubes to the burners. Tighten all connections. Do not over tighten.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.
Parts Used:
Burner Tube - Left Front Burner Tube - Right Front
  • michael from The Villages, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Wrench set
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Range does not include drip pans as standard equipment.
These new pans fit perfectly.
Parts Used:
Double Burner Pan - Left Side Double Burner Pan - Right Side
  • David from Auburndale, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front burners had to be lit with lighter
My son lifted up cooktop, unscrewed the front plate to gain access to old tube burners, removed and replaced with new parts.
Parts Used:
Burner Tube - Left Front Burner Tube - Right Front
  • Marie from Woodstock, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rats/Mice chewed wiring - valves frozen
There was no wiring harness available so we removed the block and connected all wires (with some additional wire due to the chewing). After all that, the repair went quite well. Parts arrived in about 3 days....everything's back up and running.
Thanks again for your help and prompt service!
Carol
Parts Used:
Burner Control Valve Medium Burner Bracket
  • Carol from Somerset, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
6 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light keep burning out in oven.
Remove the door. Just open a little and pull up. Removed racks. Removed 3 screws with nutdriver. Pulled out housing. Disconnected 2 wires. Assembled new housing with with bulb receptacle and gasket. Reconnected wires and crimped a little to make them snug. Pushed housing back into hole. Put 3 screws back in, inserted bulb and cover. Slid door back on and done. 30 minutes at most.
Parts Used:
RECEPTACLE PUSH-IN HOUS RECEPTL Gasket Oven Light Light Bulb - 40W
  • john from Mc Kees Rocks, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Deflector oven/gas flame deflector replaced due to hole melted from glowbar igniter
Removed oven convection fan cover for more room to remove/replace lower oven bottom. Deflector is attached underneath oven bottom and you will need new self tapping sheet metal screws to replace old ones. My deflector actually had hole melted in it from glowbar igniter directly underneath it. Glowbar remains white hot until selected oven temp is reached...poorly designed.
Parts Used:
DEFLECTOR OVEN
  • Barry from Coventry, RI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dropped & broke the oven light bulb cover
popped the new one on!
Parts Used:
Light Cover
  • joseph from san jose, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burnt food on the pans
replaced the parts
Parts Used:
Double Burner Pan - Left Side Double Burner Pan - Right Side
  • Shelly from Phoenix, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace drip pans on stove top
took off old ones and put on new ones
Parts Used:
Double Burner Pan - Left Side Double Burner Pan - Right Side
  • April from New York, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace old discolored pans
I am retired Industrial Arts teacher with two masters degrees in education. I have 35 years of experience teaching children ages 12 - 18 to safely use woodworking tools and build furniture. I also have 40 years of experience in the remodeling and construction trade. This fix was fairly easy since I was able to draw on my vast experience that included repairing and rebuilding numerous machines and tools.
The Process: remove old ones replace with new ones.
I am very satisfied with my experience with PartSelect.
Parts Used:
Double Burner Pan - Left Side Double Burner Pan - Right Side
  • Phillip from Pittsfield, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner had a hole burnt in it, glow plug broken
Removed burner and replaced
Parts Used:
Burner with Igniter
  • Thomas from Columbia, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
1 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electronic Control was fried due to electrical surge
Very simple, removed the face of the stove and unscrewed the electronic control, disconnected the wires and reinstalled new part in the same order.
Parts Used:
Electronic Control Thermostat Knob - Black
  • richard from clarksburg, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
0 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I needed an oven with three racks, mine came with two.
just slipped it in
Parts Used:
Oven Rack
  • BETTY from CYPRESS, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
uneven flame and sputtered, burner was not useable
Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect
Parts Used:
Burner Head - Large - 12K
  • glen from felch, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RGB746HED3WH
91 - 105 of 146
Back to Top