RB757BC4WH Hotpoint Range - Instructions

I simply followed the instructions on the PartSelect website. Since the range is 20 years old, I replaced all four terminal blocks. I used needle nose pliers to carefully nurse the old terminals off the burner controls, and used fine sandpaper to burnish the male contacts on the burner controls. Since the failed terminal block wire had overheated, I burnished the burner contacts that slip into the terminal blocks to eliminate any resistance that could cause overheating. So far, all burners are working great!

took 5 minutes with a nut driver and son. I had previously watch your video and went exactly as the video described and showed.

I pulled the range out, unplugged it, took the back off, unplugged the old terminal block and removed it. Attached the new block and ran the wires through to the back and plugged them in. Reattached the cover on the back of the range, plugged the range back in and pushed it back into place.

My wife could open and close the drawer without too much difficulty, but occasionally, it would not close properly and she would have to empty the contents do could alaign it properly to close. The last time she was talking about buying a whole new drawer. I asked her what the part looked like, as I never to fight with it. I went online and found the part for $1.16 plus shipping at $8 plus. It was well worth the time and effort, and I now have a happy wife. Paul Parker

I watched the video on this website and it couldn't have been easier. The only thing I did differently was I took the door off for an easier reach. To take the door off, you open just a little and pull up. It makes it so much easier to get at the screws, and maked the repair a snap.

Shut off power at the panel to the electric oven. Removed 2 phillips screws holding bulb unit in place in the top of teh oven chamber. One wire was so frayed it came out of the push on connector. Stripped off insulation and reinstalled onto the connector, using pliers to snug the wires down. Installed the new porcelain socket from Parts Select, replaced the unit in the top of the oven unit. Installed a new bulb, then snapped the new glass housing into place with the existing retaining wire clip. Presto: works like it's brand new. Thanks to Parts Select for the right parts, and for such quick delivery. I will use them again!

Removed the two screws from the range's top and the rear zinc cover and replaced the two front clip receptacles. It took me 30 min to finish the job.

Replaced them all. Next I want to replace the burners.

Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

I pulled range away from the wall and pulled the electrical plug. I removed all of the heating elements and raised and secured the top panel.I then removed the one screw that held the terminal block in place.now I went to the rear of the range and remove six screws that held the top cover in place.I now cut the two wires going to the old block,I pushed the new wires through the back panel.I installed the new terminal block using one screw. Now I went to the rear and removed the old wires and installed the new wires. I rolled up excess wire and secured with plastic ties. I installed the rear cover using six screws,I put electrical plug back into outlet,pushed range back in place,lowered front panel,replaced all the elements and turn on left rear element.FINISH EVERYTHING WORKS. P.S. I ordered two terminal blocks,if it happens again in any of the blockes I'll be ready. total costs for both $25.55 plus shipping.

The repair was very easy. It did require a very small torx driver (I can't remember the size off hand.) and a 1/4" nut driver.

Thanks to Partselect's instructions the repair went very easy. When I was done and the wife finished cleaning the sides of the stove and the floor behind it, I was surprised after I plugged the stove back in and noticed the clock was only 18 minutes off! Awesome company to deal with, Thanks!

I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!

attached the element,pushed it back in the pocket,put the plate back on, screwed the nut and bolt back on and was done in less than 4 minutes!!