turn off electricity to stove and simply remove the screws from the heating element and put new element back in place .put screws in and turn power back on and test.
replacing rusted drip pans on a 30 year old stove.
Just lifted the electric components Remove drip plans and trim rings and replaced with new drip pans and trim. Your company was incredible in there delivery of the parts..One day. You made my husbands very happy.
I looked on Youtube for a how to video. It was accurate but the screws in my oven were NOT phillips head screws, they turned out to be sheet metal screws. I used pliers at first which was a PAIN but then I borrowed a socket wrench from the neighbor that was MUCH better!! I had wanted to do it myself to prove to my husband and son that I could but I ended up needing their help because the screws were so tight.... But we did the repair ourselves!!!
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot. 1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back. 2. Pop off the hemispherical glass cap. 3. Unscrew the old light bulb, and screw the new light bulb in its place. 4. Put the cap back. 5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Bake Element was bad and Drip bowls needed replaced
First I turned the breaker off the Range. Second I removed the two screws that held the element inplace. Then I pulled element front until I could get to the two screw which connected the wires and removed then. Removed old Bake element. Installed new element by connecting the two wires and then pushed the element into place and secured it by reinstalling the two screws. Turned the breaker back on and tested. This is a very easy item to replace and takes very little time.
Unplugged the range, took old elements out, put new ones in. Couldn't have been easier and for the total cost of about $60; I have a working oven again. A LOT cheaper than a new $600 range!!
Ordered new burner and drip pan. New parts arrived within 3 days. Removed screw holding the hinge, removed clips from porcelain insulator, removed old burner, then installed new burner, reinstalled tilt lock hinge, replaced drip pan and ring and set burner in place. The whole installation took less than 10 minutes, and it works perfectly.
Turned off power to the oven at the circuit breaker. Pulled the old heating element from the back lower wall of the oven. Noted the position of the wires (right terminal attached to the red wire, left to the black wire). Removed small bolts holding the element to the wires using pliers. Attached the new element using screw driver. New element came with screws, not bolts. Pushed the element back into place and restored power. Tested to make sure everything worked. Everything works and I ran an oven cleaning cycle. Noticed that indicator light above the temperature selctor is always on now even when oven is in the OFF position. Not sure if that's related to the change or to the oven cleaning cycle I ran. In any case, oven seems to work normally.
Read and follow the instructions. Be careful when stripping old wires to attach to new element. Fit the element to ceramic casing prior to attaching wires. If new element does not seem level after replacement heat a large pot of water. The element will expand and the weight of the pan of water will settle the element. "Physics 101"
Took off the door, took out the two screws in the back of the element. Then pulled the element forward, then removed the two wires. Then put it all back together with the new element.
A friend had stopped by and insisted on replacing the heating element on my 32 year old range. It took him all of 45 minutes to replace it, and now it works like a charm.
removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires. Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.