Models > RA720K1WH > Instructions

RA720K1WH Hotpoint Range - Instructions

All Instructions for the RA720K1WH
46 - 60 of 140
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burner would not stay in socket
I pulled off the back panel and the two wires were attached to the back of the know for the burner that did not work. I unhooked the wires, fed the new ones into the same slot and clipped the block in place. That was it!
Parts Used:
Surface Burner Terminal Block Kit
  • Jack from Georgetown, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fix prior jimmy-rigged repair job
Prior repair job had spliced the terminal block wires with electrical tape; electrical tape caught fire while making pasta.

anyways, disconnect all power, remove burners, pull stove out. you'll need a 1/4" drive socket to get the back cover off; six bolts total. phillips head screw driver to unscrew the terminal blocks; replace with new terminal blocks; it did not seem to matter which wire plugged into the back. put everything back together. very easy.
Parts Used:
Surface Burner Terminal Block Kit
  • Jason from Charleston, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
support clips fell out
Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.
Parts Used:
Single Heating Element Support Clip
  • tomi from dallas, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element blew hole in self then no power to burner.
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Parts Used:
Range Surface Element Control Switch - 6 Inch - 1560 W
  • Melvin from Portland, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hanging broiler
Quick and easy, thanks!
Parts Used:
Single Heating Element Support Clip
  • Doris from Aberdeen, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Could not adjust heat on burner.
Followed directions given by previous customers problems which we found on the internet.
Parts Used:
Surface Burner Switch - 8 Inch - 2500W
  • Roy from Au Gres, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip bowl from a big box store was too big even though both say 8”.
Ordered the part and set it in.
Parts Used:
Drip Bowl - 8 Inch
  • Kathleen from INCLINE VLG, NV
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner terminal block was worn out
I unhooked the main power cord, unhooked the worn out block terminal cut the tape that was holding all the wires together. Removed the back panel and followed the wires unhooked the 2 wires and installed the new block terminal. Tied all the wires back, attached the back panel and plugged the power cord back into the outlet. i tested the burner to see if it was working. The burner is working great, instructions were easy to follow and my wife is happy. Thank you
Parts Used:
Surface Burner Terminal Block Kit
  • Mario from RENO, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The terminal block broke
Replaced the terminal block and used hi-temp wire connectors to place the new part into the circuit.
Parts Used:
Surface Burner Terminal Block Kit
  • Karl from WINONA, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed new drip bowl, was very hard to find one that fit my stove
Installed easily, was most impressed with the speed of delivery and it was the perfect size!!
Parts Used:
Drip Bowl - 8 Inch
  • Rosemary from BROOKFIELD, CT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip pan was ruined by renter
I ordered a new drip pan. Piece of cake. Stove looks new again.
Parts Used:
Drip Bowl - 8 Inch
  • Karilyn from KEWADIN, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
It was burned out
I just follow Steve's Installation Vidio. My range works.
Thanks Steve
Parts Used:
Surface Burner Terminal Block Kit
  • lan from SANTA CLARA, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The temperatures had worn off on the old theramostat,
All I had to do was push the thermostat on the hinge.
Parts Used:
KNOB THERMOSTAT ASM. GE
  • ALVIN from ALBUQUERQUE, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner was not heating
unplug it and plug the new one in
Parts Used:
Surface Burner Terminal Block Kit
  • lucille from HAPPY CAMP, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced the outlet the one of the top burners on top of my stove, it went very well.
I followed the instructions on the video, the only thing they left out is where the wires go through to the back of the stove being that there are sharp edges. A role of glass tape would have been handy to replace the old tape. Thanks for asking, I hope this helps someone else.
Parts Used:
Surface Burner Terminal Block Kit
  • Charles from MECHANIC FLS, ME
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RA720K1WH
46 - 60 of 140