NVLR333ET0WB Hotpoint Dryer - Instructions

This repair was a no brainer repair. The factory replacement knob that I bought from this site comes with a new "D"-Ring. Some other aftermarket parts houses sell the knob and the "D"-Ring as seperate parts. The knob from this site already has the "D"-Ring ring installed in the knob. My "D"-ring was broken and I simply removed it with my fingers. All I had to do was properly align the new know knob with the timer shaft and press it into place. If your "D"-ring is not broken and not still inside the old knob, you will need to pull it off the shaft with a pair of pliers before pressing the new knob onto the timer shaft. Dr. "B" The Hot Rod Doc

Unplug the AC cord. Open dryer door and unscrew 4 small Phillips screws that hold the top panel to the front panel. Tilt up the top panel.
To remove the front panel: Look on the inside of the front panel, disconnect all the wire connections that go to/from the front panel, such as the light and door switch. Remove 2 screws that attach the top of front panel to the side panels using a 8mm or 5/16" wrench. Undo or loosen 2 Phillips screws at the bottom of the front panel, one at each bottom corner. Remove the front panel. Go to the back of the dryer. Remove the 8 screws holding the lower access panel (8mm or 5/16"). Remove the access panel. Also, remove the 2"x4" access plate in the center of the back panel (2 8mm/5/16"). Reach inside the small panel opening with a needle nose pliers and remove a Cir-clip and washer that holds the rear drum bearing shaft in place. Now you can remove the drum straight forward. Clean, clean, clean the insides. Replace the worn drive belt, follower wheel and front slider pads as needed. Reverse the procedure to reassemble. Plug in and test. Drink beer.

stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.

installation exactly how your directions told me on the computer

This is kind of embarrassing but ... Originally checked this site for what to get for the symptom and said 61% of time was high limit thermostat which was fairly cheap (14.95) but assumed with my luck, it would be the more expensive part the heating element coil with housing, so ordered that. (It was second on the list) Received it in no time, like less then 48 hrs. Was told when a friend stopped by that I shouldnt of ordered that, it was probably a thermostat as that is what they had to replace on theirs. So I said ok, I could always send the first thing back, so ordered the thermostat. It came quickly again. Took it out of the package and laid it down to change clothes to take the dryer apart and could not find where I laid it. Spent all evening looking and never did find it! So I ordered another one. (Figured by this time PartSelect was thinking this woman is crazy but good for business) Again it came quickly. Got it on fine but when I got to check the old one with the ohm meter (which I borrowed), nothing wrong with it. Nor with any of the other 4 thermostats. Finally took the drum off ( thanks to Youtube video for instructions) and obviously it was the initial part that I had ordered that needed replaced. Was a bit awkward to remove all the screws to get to it but not bad. Plugged everything back in and got the machine back together and works wonderfully! Lessons learned: 1st check the elements with an ohm meter (I will definitely be investing in one) 2nd do not open package until ready to use it especially after a bad day at work and 3rd go with initial gut instinct! I was very pleased with Part Select service!

Removed four allen head screws to expose inside of panel. Used flat blade screwdriver to raise spring retainer and turned switch counter clockwise to remove.

Per suggestion of "Parts Select", I replaced the "high limit thermostat"....very simple task on the dryer: 1 - unplug from power source; 2 - remove screws securing top to front (open door, screws located beneath lip of unit); 3 - tilt top up allowing access to everything; 4 - remove connections to 'thermostat' (note which wires go where); 5 - loosen screws securing thermostat to unit and remove thermostat; 6 - vacuum any and all lint while unit is apart; 7 - install new thermostat and put everything back together; 8 - test dryer to see if repairs worked!

Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.

Replacement is easy = Tilt net for lint into opening and set by snapping left side then slide to right to seat into proper seal. Do not force either side when seating.

Found excellent instructions and diagrams online by searching under the model number. Best of all was the service from PartSelect. Belt arrived 24 hours after ordering. It was the right part, it was easy to install, and the dryer is running beautifully.

Took the top and front off. DO NOT TAKE DRUM OFF!! Lifted drum slightly and worked belt around drum. Replaced front and top. Took off rear panel at bottom near vent pipe. Put belt around motor and then tension pulley. Buttoned everything up and that was it!

Replaced the filter. Was very impressed how quick I received the product, no hassel... Nice...

Removed top panel from dryer. Unplugged the 2 wires for swithch, rotated swith, and removed. Reversed the process. Put parts back together.

I removed the two screws from inside the door at the top, which were holding down the top.

Removed top,then two screws at the top of front in the inside of the unit

Tilted out the front so the wires would not come disconnected, slip in new bushings, and put it back together.

Thanks,
Saved me from buying a new dryer

First unplug the dryer from power. Now open the dryer door and remove the two phillips head screws that hold the top down. Then lift the top off and turn the dryer on it's back (this is not necessary but if you have the room it makes the job easier). Now remove the two hex head screws that hold the front on and remove the wires from the door switch. Now you can lift the front of the dryer off, door and all. This now allows you to replace the three (on this model) slide bearings and the felt. I also removed the belt and lifted the drum out and checked both the belt and the rear bearing. You can do it!