MSD2656GEQ Maytag Refrigerator - Instructions

My ice maker was overflowing and i realized that it was the water valve that needed replaced. unscrewed 1 nut, unhooked 3 water lines, unhooked electrical components and re-installed in reverse order. took about 10-15 mins.

I removed all contents from the lower shelf. I, then removed both of the pull out drawers. Secondly, I removed the lower glass shelf and the glass support tray. At this point all four plastic shelf supports were accessible. I removed the inner screw from all four supports and replaced with four new shelf supports. Then reassembled in reverse order. Very easy to do!

first i remove the two screws like the guy said on your web site. then i pulled the cover off with a upward motion revealing three more screws witch i removed. I then removed the dispencer. unpluged the wires and removed the switch and pad and replaced with new parts.I reinstalled the wires then the unit, installed the screws and cover.Checked for proper operation.Then enjoyed that cold beer! Thanks to your wed site and repair info. I saved at least 100 buck to the repair man. Thanks Partselect.com

I bought the following parts:

PS109042 Double Outlet Water Valve
PS46363 Dual Outlet Water Valve Kit

When I bought the fridge, the part that PS109042 replaces was cracked and leaking water badly. When I ordered the replacement part, I got confused and ordered PS46363 by mistake. The original parts look similar even when side by side, but the replacement parts are revised drastically.

PS46363 is for the line that is between the water source and the water filter. The original lines from the filter are split (the original part has two inlets) and pipe to one inlet. You'll have to cut your hose right before it forks. The directions that come with the part are very straight-forward.

PS109042 actually distributes the filtered water to the water dispenser and icemaker. The old part had plastic fittings that held the water hosing to the part. The new part has no plastic fittings, yet holds the hosing to the part tightly. The directions that come with the part are very short and concise.

I also replaced the factory water filter with a Brita replacement (they are cheaper and I've used Brita filters before...they are solid).

All in all, I spent less than $100 on fixing a $500 used fridge that works as good as new. My wife was initially doubtful but fairly satisfied with the cost of the parts and the simplicity of installing them.

As the previous users have stated, remove the ice tray, then remove the ice bin enclosure. Watch for the screws that are used to mount the enclosure.
As you slide the enclosure forward, go slowly, there is a wiring connector at the back, you will need to un-plug this connector. The solenoid assy is kind of tricky, as it is spring loaded, but easy to figure out. As previously mentioned, the auger yoke is on a shaft that has to be removed by turning it clockwise (reverse threads). Be careful with that, as it is hard to hold on to the shaft while getting the yoke off. Now remount the motor, remount the spring loaded solenoid assy, slide the ice bin enclosure back in a ways, then reconnect the wiring harness, slide it the rest of the way in, tighten the screws, and you are ready to make ice again. Approx 30 minute job.

Easy to diagnose problem because there was water to the water dispenser but none to the newly installed icemaker. Originally did attempt to clean the solenoid but found the plunger assembly damaged.

New part arrived sooner than I thought it would. Takes about as much time to remove the lower vent cover as to replace the valve. Remove the electrical plug from the wall, valve off the main water supply, remove lower vent cover, disconnect the supply hose from refrigerator valve assembly, remove one hex head mounting screw and you have both water valves in your hands. Identify the valve the supplies water to the filter and the one that supplies water to the icemaker/water dispenser. Then confirm which plastic water supply line goes to the water dispenser and which goes to the icemaker. Hose diameters are different but it is good to know. Disconnect the plastic water supply lines from both the ice dispenser and the icemaker portions of the valve. Replacement solenoid valve does not have thread on type compression fittings. Snip about an inch off of each hose and then press into the appropriate valve orifice.

Making sure the plastic supply lines do not get crimped, remount the valve assembly, reattach the supply hose, valve on the water and check for leaks. No leaks, reinstall dust cover and plug the refrigerator back in.

Move the unit back in place and then take a long deserved beer out and have a celebratory toast for a job well done.

(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!

I called PartSelect and was greeted by a real live person instead of a recording. The lady was very helpful and kind. We decided on the part that I needed, and it arrived to my home in less time than she said it should. I completed the repair with the instructions provided in just a short time. My experience with PartSelect was positive, and it reminded me of the way businesses used to be. I highly recommend them.

Thanks to previously posted PartSelect stories, I had a good idea on how to proceed. This component, as others have suggested, is clearly a piece of junk. This is the third time it has been replaced, once under warranty, again in a service call for $160 and now by me, with a PartSelect unit for $52.
The circuit board, with integral relay, resides in the extreme upper right hand corner of the fresh food compartment.
Remove upper shelf.
Remove white plastic control cover through which the lights illuminate the compartment. Finger grips at both sides at rear. Slide forward about an inch to clear the tabs visible at the rear, then tilt down and off. The owners' manual describes this at "Changing the Light Bulbs". It also gets the lightbulb description wrong, but ..........
Now remove the hex head screw facing you at the rear center. Then get its two cousins which are vertically positioned to hold the front of this housing up into the roof. They're left and right, just rearwards of the ends of the control setting dial.
These three tapping screws which you now have in hand are about 1 1/4" long.
Next, there are two Phillips head screws, also into the roof, whice are just to the rear of the two light sockets. Removing these, and the left one is awkward, frees up the control totally except for the wiring harness, which restrains it at the rear.
No matter, just tilt the unit down so that the front lip is pointed down towards you.
The piece-o-crap board is at the right rear.
Pop off the connector, takes some force, and put in your new module.
Order another one now, you will need it.
The service tech who changed out my next-to-last one left a circuit diagram back there with the new control, like saying "I'll be back."

took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks

I had to cut off the old yoke since the threads had stripped and it would not come off. Once I did that all I had to do was to remove 4 screws on the auger motor and replace it with the new auger motor. Then I put the yoke on the new auger motor shaft and then put the unit back in the freezer. Work time was less than 15 minutes with no problems.

Took out all shelves and racks. Pulled out plastic cover. Removed screws holding control unit. Removed unit and accresses defrost circuit board. Replacement is in a cover. One screw would not engage so did not put it back in. Reefer was cold within hour of start and is now 1 week after. Unit would start out cold and then warm up before replacement.
Other parts were snap in furnishings that had become damaged with use.

I called a repair man from a pretty large name to come out and take a look. He found out in about 10 minutes that it was a bad capacitor. The quote he gave me was $75 for the part and $175 labor. I tried my best not to laugh and tell him no thank you. He did have to charge me for him to show up, which was only $98.
So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.

First I hired a repairman to fix it who charged $125 to defrost the cooling coils then said the defrost heater would need to be replaced for $125+labor. He had the wrong part and was going to charge me >3x the price it would have been from Partselect.com too. I figure I saved a minimum of $250 vs having him do the work then charge me yet again for the right part.

Should have just done this myself from the start and saved another $125. Information about the cause, how to test and what parts would be needed were all easy to find online once I actually searched.

Unplugged fridge.

Using diagrams from PartSelect.com and other information online anb defrosted coils with hair-dryer. (This requires removing two screws in back of freezer compartment using nut-driver to remove the panels covering coils... literally a two minute job to expose coils!)

Then found and tested defrost heater.
Defrost heater was fine. Per information online problem then had to be Adaptive Frost Control (ADA) circuit board.

In refrigerator compartment:
1) Removed top housing cover (covers lights, temp controls, etc.) This required removing a single screw (with nut-driver) attaching it to back and depressing two locking tabs near the back on either side. Slide it forward and down. The only tricky part of this repair is getting the locking tabs positioned correctly to get the plastic cover off. I did break the left one although it cover is still firmly in place in this case.)

2) Removed entire assembly from roof of fridge. involves loosening two large headed screws above lights and removing two hex-head screws with nut-driver above either side of temp controls. Next slide slightly to the right to disengage the two large-headed screws (or remove them completely... it seemed easier to just leave them in place.) Dropped front end of control assembly down.

3) Opened plastic box surrounding ADA and pried open locking tab holding it to wiring. Connected new board and set ADA assembly back in place.

4) Put everything back together.

Plugged fridge in and all was well. Exposed the coils again a few days later and they were not frosted up at all.

Total time to replace the ADA was about 20 minutes. Total time for everything including defrosting coils, testing, replacing parts, etc. was an hour max.

First I removed the spill tray, and removed the two screws on the bottom of the dispenser. I was then able to remove the front of the dispenser, which revealed 3 more screws. After removing those screws, the entire assembly lifts out. I removed the old pad, put the replacement pad on, replaced all the screws and the tray, and was done! It took about 10 minutes, start to finish. I saved at least $75 on the repair by doing it myself, and the part only took 3 days to arrive. Best of all, the water and ice dispenser works like new! Thanks, PartSelect!