Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dropped the glass cooking tray and it broke in half
Looked up the Whirlpool Co. and ordered the part. It was quite simple. Arrived in 2 days and I simply placed it in the microware. It was very very easy!
Loosened but did not remove screws that held up microwave over range,removed grill on top by loosening screws that held grill in place.removed small mesh grill on right side of microwave, this gave me access to capacitor ,diode is connected from one lead of capacitor to a metal plate ground,Disccarged capacitor to ground by shorting terminals to ground using a thick insulated screwdriver.Since the diode was screwed to the top of the metal plate I cut it out with a pair of side cutters .I then connected the new diode to the capacitor with my long nose pliers and groonded the other end to a more accessible part of the metal grounding plate.I then replaced all parts in reverse order.Works like a charm.
After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)
The old coupling melted and the tray cracked in half.
It took me 15 minutes total - 5 minutes to clean the microwave, 1 minute to install three new parts, and 9 minutes to enjoy my celebratory glass of wine!
Exterior light bulb (PS2376034) broken off in socket. No access for pliers after glass cover removed.
Unplug appliance. Remove total of 7 phillips screws from sides and front of bottom panel . Panel front drops down, remove one socket screw and socket. Now have access for lineman' s pliers to unscrew bulb base. Reinstall socket, replace bulb and 7 panel screws. Restore power.
Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together
The grease filters you sent to me are not the same size as the filters I replaced!!! Since the new filters do not fit correctly the air does not get filtered since the filters are too small for the hole. Why would you send me replacements that are not the same size as the ones I replaced? The filters are in the hole of the original ones but are too short. Not happy with this transaction at all!!!
I had to cut the leads on the thermostat to enable the wire terminal clips to fit on the leads. Not hard at all when the right tools are available. Care must be used because the leads are subject to being damaged. “ Hold leads with narrow needle nose pliers while cutting!
Removed the face plate above the door (2 Phillips screws.) Removed existing filter and replaced with the new one purchased. Reinstalled the face plate.
Very unusual. we had a brief fire inside the microwave which destroyed all the moving rotary parts.
First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple
Took microwave off the mount, removed all the outer covers except the face, used metal screwdriver to short the big capacitor to keep from being shocked, removed magnetron and replaced with new part. Put back together, hung on wall, and finished. I used a youtube video and it turned into a very simple fix.
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place. Snapped off the top control panel which exposed the wiring connecting the control panel. Unplugged a couple of wire harness units to free the control panel. Be sure to label the units to know which goes where during reassembly. Remove the microwave unit from the housing and place it on its side. Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.