MER6755AAW Maytag Range - Instructions

Removed oven door and rack. Removed two screws holding element. Disconnected wires to element. One of the wires slipped into the back wall of the oven. The range had to be removed from the counter and back panel removed to gain access to the element wires. Install new bake element in upper oven. Connect wires to element spade lugs. Install rear panel. Restore power at circuit breaker panel. Very important - aways disconnect power before starting work.

I viewed the YTube Video that showed exactly how to remove the door and all the other parts for replacement. Excellent video shows and explains how to remove, replace, and re-attach the handle and the door.

I didn't. Don't know how to get to light bulb to change it for this specific model

Turn off breaker in electric panel fore stove. Put screw driver into slots in front of glass top surface. Pry top up carefully until top pops up.Remove burner dial, remove two philips head screws holding switch. Lift top carefully and prop up.With new switch close remove wires from old switch one at a time and place on new switch. Place new switch back in place, securing with philips screws. Remove prop and carefully press top down until it snappes into place.Replace dial, turn breaker back on and try burner.

1. OPEN THE OVEN DOOR TO THE FIRST STOP,
PULL UPWARD TO REMOVE, ( IT WILL LIFT RIGHT
OFF)
2. LAY OVEN DOOR ON A FLAT SURFACE ( HANDLE
DOWN AND HANGING OFF SURFACE) WITH A
TOWEL TO PROTECT THE GLASS.
3. REMOVE ALL SCREWS AROUND THE
PERIMETER OF THE DOOR..
4. CAREFULLY SEPARATE THE DOOR FRONT AND
BOTTOM BRACKET BY SLIDING AWAY FROM
THE MAIN DOOR INNER-ASSEMBLY, ( THE
FRONT GLASS IS HELD BY THE TOP CHANNEL.
5. TURN THE MAIN DOOR INNER ASSEMBLY OVER
AND REMOVE THE HANDLE ASSEMBLY TWO
ATTACHING BRACKETS.
6. REMOVE THE ATTACHING BRACKETS FROM
THE HANDLE AND ATTACH TO THE NEW
HANDLE.
7. THE DOOR GLASSES CAN NOW BE CLEANED
8. ATTACH THE NEW HANDLE ASSEMBLY
9. REASSEMBLE IN REVERSE ORDER.
( BE CAREFUL WHEN SLIDING FRONT DOOR
GLASS INTO THE TOP DOOR CHANNEL}

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

turn off all electric to the wall oven. removed the old broiler. replaced the new broiler and turned on the electric. checked the brolier one to see if it worked....it did thanks for the customer service for her help in finding the replacement part.

Shut off power at breaker box , pull stove away from wall , remove Phillips screws from back of range pull knob off of switch . Look to see how switch is oriented remove 2 screws that hold switch in . Remove one set of wires at a time and place on new switch in same location . Put back together in reverse order .

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

My grandson, age 15 did the replacement. Now, how easy is that!

Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.

My 4 year old son managed to break the oven door glass. The repair man asked for $175 to fix it
I had ordered the door kit from Part Select and it arrived earlier than promised. Fifteen minutes later I had it in place. The cost $49.64
Thanks Part Select,

Peter Lobo

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.