I followed the repair videos which were very helpful and made the job easy to do. Anyone of average handyman skills should be able to perform the repair without difficulty.
Dryer wouldn't start. For months it had made noise and would require a long cool down between loads.
Several times I watched the video of "Steve" removing the old motor and installing the new one. Pretty much followed what he did. Faltered for a moment at the end reinstalling the drive belt as that was a blind procedure, done by feel. Hardest part was getting the spring clamps off the old motor; even Steve struggled a bit doing that part of the job on the video. But in the end, the dryver started right up and ran quieter than it has for months.
Removed front of dryer, removed inner cover, slid roller belt off of drum to remove drum. Only tricky part was the two clip rings. My pliers had .070 tips and the ring holes were smaller so I had to run to HD to buy a pair with various size tips, ended up using the .047 tips. Only one wheel was squeaking when I rotated them by hand, but I had ordered both as recommended here so I replaced them both. Put everything back together feeling the belt to make sure it was not twisted and rolled smoothly when I rotated the drum by hand. Works great now. Lots of thanks to this site and all the posters who share their info!
High pitched squeal would wake up the neighborhood.
I've had this dryer since it was new It's over 25 years old. and it started to make a high pitch squealing sound when in use. Decided it's time to repair it. a new one is very expensive. So I ordered the parts from this site. When the parts arrived they where Inspected for fit, function and finish. So I proceeded with doing the repair myself. Short Phillips screw driver to remove the two sheet metal screws at the bottom front panel. tilted the panel from the bottom outward and removed it from the main tumbler cabinet. labeled the door switch wires one was yellow & one white. so I would not reinstall them incorrectly upon assembly. removed the front panel. set it aside. then removed the bulkhead panel 5/16" screw in each corner. removed that and set it aside. and there she was, the tumbler. I pulled the tensioner up to loosen the belt, and removed it. then grabbed the tumbler from the inside top slightly picked it upward and slid it out of the cabinet exposing the two rollers and axles one on each side that it sits on. at that point I noticed the drive belt was frayed and slightly worn. came back in the house and got on line ordered a new one from Parts Select it showed up a day later and a perfect match. the rollers are held in place by snap rings at the end of the axles. squeeze them they come off real easy, and on the back side there's a 14mm hex head nut. box wrench works good here to loosen the nut and remove the axles. the original washers are metallic and worn badly, they where making the high pitched squealing sound when they rotated so they came off and where replaced by the ones in the new roller kit and lubed with graphite not oil or grease. Graphite is dry and does not collect all the dirt and debris. put the new washers, new rollers & snap rings back on the axles grooves on the end, hand spun them and they where ready to roll. took the new belt placed it around the tumbler over the exact witness marks that where there so it would line up and lifted the tumbler back into the cabinet aligned the new belt over the motor pulley and tensioner lining it up exactly on the witness marks left by the old belt. slowly slid the tumbler back on to the new rollers rotated the tumbler a couple rotations clockwise to set the belt put the bulkhead back on the front with 5/16" sheet metal screws. in 4 corners, reinstalled the from panel along with the door switch wires and it was done. now the moment of truth. plug the machine in and turn it on!. Bingo! it runs so well you don't know it's even running. after this repair the machine performs even better. it actually takes LESS time for clothes to dry! AJS
Drum roller was squealing loudly every time the dryer was used. Sounded like a car's power steering belt squeal only 10 times louder.
I watched a video on YouTube for the disassembly of the dryer. The parts replacement took less than 20 minutes; the rest of the time was spent on disassembly and reassembly.
I began by removing the two screws at the lower part of the front panel. After removing the panel I was able to access and remove the broken switch which was located on the front panel. I popped out the old switch and replaced it with the new one, reattached the wires and put the front panel on and the jod was done.
Unplugged the dryer (don't forget this step guys!!!)
Pulled the front off the dryer (4 screws) and swapped the motor out - take off the belt, pull the blower wheel (by removing the snaprigs and squeeze collar), then pull off the motor retaining clips... unplug the motor and install the new one in reverse. Took me less than 2 hours and my dryer works like new.
With the parts in hand, and after disconneting power and shutting off gas line, I again removed the door, front panel and front tumbler frame to expose the blower wheel. I discovered that the blower wheel was not damaged, but that compressed pieces of lint and other items where stuck to the wheel. I removed the pieces and vacuumed the the whole thing clean, tested it, and the sound stopped. Since I had the unit open, I replaced the front glides by drilling out the old rivets, removing the old glides and then riveting the new glides in place. A very simple procedure overall.
Make sure you keep track of where the different screws go and keep them inside something so you don't lose them. I also used my cell phone to photograph various areas and screws for later reference.
shaft had become worn , making loud noise and also causing drum roller to wear prematurely.
first, i removed two screws at the bottom of front panel. then lifted from the bottom removing it. next, removed drum surround and drum. next , removed right roller and roller shaft. then installed new shaft, slide roller back on shaft. next reinstalled drum, drum surround and front panel. Now so quiet you can hardly hear it run, also my sister says it drys much faster.
removed front door, removed front panels, lifted top back, unhooked belt, removed drum and belt, removed blower housing front, removed squirrel cage, removed blower housing, unplugged motor, removed motor assembly , ..switched new motor to motor cradle ... reversed process.
