MDC5100AWW Maytag Dishwasher - Instructions

First, I removed the screws that hold the interior part of the door in place. Next, I removed the two screws that covers the interior parts of the latch release in place. Then, I removed the broken latch, put in the new one and attached the spring. I put the pieces back in place, and the two screws back in. Finally, I screwed the door panel back together.

Took old one off , installed new one!!

The problem was the rubber end on the upper shower head pipe at the pump. Not to hard . Slide dishwaser half way ouy the ptpe is on the right side.The bottom end is is just a clamp the top drops in from the top, inside there is a nut above the upper shower head. You can unsrew the nut with your fingers, it is right above the upper shower head.There it a washer at the top of the pipe that should be replaced that doesnot come with the pipe

Orderd the part's from your web site (recived my order in a timley fasion thanks) the parts just sliped on and clipped' basket rolls great. Mike Schaffer

I undid the four clips that attach the upper dish rack to the dishwasher. The upper arm simply unscrews from the top of the dishwasher. Unsnap clip that holds arm and remove arm. Installation is the reverse of removal.

I followed instructions of others that were posted. Door seal was simply removing old seal, cleaning track and pushing new seal in,making sure it was even all around. Removing the door cover to get at the Dispenser grommet was simply removing all 7 hex nut screws. Had to go out and buy the proper hex nut screwdriver . I did not remove the wiring, just turned cover over to remove the two nuts holding the dispenser. The nut on the left was a little hard to get off, had to kind of force the socket onto the nut. Otherwise all went well and simply removed the old grommet and installed new one. Finding the right tools was the part that took the longest. I had hard water before putting in a water softener so that was probably hard on the seals plus the machine was an older model. No problems now and saved having someone come in and do a repair.

I removed the old door gasket and thoroughly cleaned the track. I placed the new door gasket in place- no problems.
I had to remove the 7 screws from around the door to access the old, crumbled gasket. This was accessed by removing 2 screws with a socket wrench. The old gasket pulled out and the new one slipped right in.
No more leaks!

I first removed the bottom access panel and 2 upper screws holding the dishwasher to the counter. Be sure to remove the standing water in the bottom tray. I pulled the chassis far enough forward to reach where the top shower hose attaches ( the supply line and wire had enough slack to move the chassis ). Not knowing how the rotating shower arm attached, I unscrewed the ribbed retaining ring above it, and found the whole assembly came loose - freeing the upper end of the shower hose. Put a shallow tray under the lower end of the shower hose to catch the remaining water and loosen the hose clamp to free the remaining end of the hose. Transfer the rubber washer at the top end and the hose clamp at the bottom, to the new hose and install. A quick repair, but one that shouldn't be needed on a 4 year old dishwasher.

Unscrewed the inside door panel. Removed the reservoir assembly. Disconnected the wax motor. Replaced it with the new motor. Replaced the new o-ring. Done. The hardest part was finding out why it was not working and how to fix it. Google for a long time in order to find some idea what to do. Then took the door apart to see the reservoir and the wax motor. After that, it was pretty easy. HTH

I disconnected the dishwasher and started to take the impeller assembly apart but could not get it all apart. Went on line to start looking for the parts and came to Partselect and they had and exploded view of the the whole inside assembly and I saw what was wroung, some parts had broken and melted together. With this picture I was able to see what had happened and able to get it all apart. Ordered the bad parts, got them within a week (this was over the hoildays), took about 15 minutes to get the new parts in and the dishwasher running. It runs great now, very quiet, it's like a new dishwasher for $30.
P.S. I had to order some extra parts because one of my dogs was helping me and chew them up.

first I turned off the water to the dishwasher, and turned the power off for the dishwasher.
removed the 4 screws from bottom panel
then removed the 2 screws from the bottom of the counter,
at this point I could pull the dishwasher out. then figured out where the part went and attached.
pushed the dishwasher back and lined up the holes under the counter, put those in first, the put the bottom panel back on, turned the water back on, and flipped the breaker switch.
Reading the other stories really did help me get some idea of what needed to be done

Although the (top) dishrack assembly included the nylon wheeles, it was easier to replace the old one by disengaging it from its wheels and installing the new rack on the old wheels kept in the slider track. The snap hook that held each wheel to the old rack was popped loose (finger pressure) and the old rack removed. The new rack was held in place and each of the four wheels snapped to it. Each wheel fits into a wire post on the basket and the plastic hook snaps onto the wire frame. The most difficult part of the 'repair' was removal of the handle from the old silver ware basket. I used screwdrivers to simultaneously pry the four tabs of the halde out of the slots on the basket and pulled (hard!) the handle off. It snapped easily into place on the new basket.

purchased disk rack was complete exept for the water diffuser in the middle of the rack. Merely pulled to old rack out with no tools, twisted out the diffuser and tweisted in to the new rack.

No tools or instructions required.

The rack assembly was not altogether assembled. Had to remove one part from the old one and reassemble on the new. Also, The racks that make place for a bowl instead of plates was not assembled.

Initially I suspected something had found its way to the impeller or the macerator, began to disassemble top down. Upon removal of the discharge it was apparent the plastic disc at the top of the discharge was sheared off. Located the schematic at PartSelect and ordered the discharge. Received part within 3 business days and installed new discharge in about 30 minutes. Required 5/16 socket and hex head driver. Recommend ordering new gasket with part.