MDB9150AWS Maytag Dishwasher - Instructions

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

First you must understand that the end cap is not a solid piece. The plastic facing you is wrapped over the piece behind it. The separation may be obscured by age. Wedge thin bladed screwdriver into the outside edge of end cap at the bid point, a sturdy hunting knife will probably work better. When you hit the seam, pry it apart and fold it back. Unwrap the part and repeat on other side. The dishracks will easily slide out and in.

Snapped old ones off and snapped new ones on.

Excellent site. When the dishwasher started making a loud grinding sound, i thought "oh great -- now I'll have to buy a new one". After searching the internet (I just entered the model number of my Maytag dishwasher), Partsselect.com came up in the search results. I read several postings from previous customers which described the same problem I was having... followed their step-by-step instructions and was able to disassemble the lower washer arm and find the culprit -- a broken wash impeller. Ordered the parts, they arrived within a couple of days, spent 15 mins putting everything back together and I'm now good to go! THANKS PARTS SELECT!!!!! I owe somebody a free lunch!

I simply looked at the other side (which was still functioning) and put the new one on but in reverse (left side/right side) I also was missing the end stop to the slide and simply popped that in and snapped closed. Two simple parts and 15 mins. solved a whole lot of aggrivation,
without any aggravation! wish I had found this site sooner!

my husband took the bottom rack out, unscrewed it where there were screws, lifted up the unscrewed part, took the filter out,cleaned out any gunk, replaced the filter put the part back on, rescrewed it, put the rack back in and it works much better.

Removed the screws to the front panel along the inside of the door. Replaced the broken part with the new one. The only glitch was I needed a screwdriver to pry one end of the new part to seat into the hole where its installed. Replaced the screws. Job complete in 15 mins.

had to fiddle around just a bit to look at the others and see how these fit in. No tools were required - just snapped into place once I figured them out.

First I removed the inside door panel, then I snapped the old latch out and put the new latch on with screws. Easy, and works perfect now.

i removed the strainer cover and then removed the discharge assembly. then repeated steps to finish.. parts select was very fast and cheap ordered ontuesday and arrived on thursday. I will recomend parts select to all

Ordered 3 parts first ..all came within two biz days..forgot the toe panel, called it was here the next day! The people that assisted me were wonderful! My husband did the repair. the dishwasher looks like new!!!!! I will order from Part Select again and again...extremley pleased. Now if only we could cover the Refrigerator in Black it would look like a whole new kitchen!

The most difficult part is learning how to unsnap the plastic retainers at each end of the steel sliders on each side of the dish rack. Push the end caps to the outside and the plastic inserts will snap open and slide off the ends of the rails in two pieces (note how they were oriented so you can replace them later). The caps must be removed from both ends of each rail. Slide out the basket. slide the rails out. Pull the old rollers off the pins. Place the new rollers into position. A smart rap with the palm of your hand should snap the rollers onto the pins. If you have done it correctly, the rollers will not pull off the mounting pins. You could also place a small block of wood against the roller and use your hand or a small hammer or weight to snap the pins into place. Assemble in reverse order.

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

Removed front access panel
Disconnected water supply
Pulled dishwasher out approximately 1 foot to gain access to spring linkage
Connected new spring linkage to spring, connected other end of spring linkage to door
Tested operation of door
Slid dishwasher back into place, reconnected water supply and front access panel

I asked my husband if I ordered the parts would he change them for me, and when they arrived, it looked so simple I did it myself. I removed the washer arm by unscrewing the disk that holds it in place. I took the metal heat deflectors off the old arm (they just easily pried off) and put them on the new. I lifted off the large round "plate" that the arm rests on and cleaned the underside. Then put it back together in reverse order.