LEA30AW (PLEA30AW) Amana Dryer - Instructions

Motor was replaced with common hand tools, after replacing roller guides and belt.

I knew that it have to be worn out roller drums or the idler pulley with bearing. So, I ordered both items. I watched the repair video to know how to do it. I installed the items and the sound disappeared

I did it just like the man in the video that was sent via e-mail by ParSelect,.

found thermal fuse and checked continuity had none so fuse was bad. ordered new one from parts select correct fuse came quickly installed new one and dryer works like new.

I opened the base door and took out the heater panel and checked with an electrical meter. The high thermal fuse was blown out. I replaced the fuse and run it for five minutes, it was blown out again. I checked wires and nothing was wrong. I replaced another fuse and ran only three loads, it was blown out again. I though that it was a sixteen years old machine, I replaced the whole new heater panel with a new High Limit Thermal Fuse and a new Limit Thermostat. It ran good for 5 minutes test. I will know when I run a few loads in this Friday 4/25/14.

replaced all above parts, everything seems fine now. Thank You.

Diagnosed with Amana Reference manual & Ohm meter. Ordered parts. Cleaned everything while parts in transit. Installed parts, completed reassembly & fired it back up. No problem.

Used the Parts Select video. I also replaced the drum belt which I had ordered earlier. Repair went exactly as described in video. Belt looked fine but replaced anyway. Rollers and glides needed replaced. (Hint: felt pads for glides had come unglued and fallen to bottom of dryer-this was probably the main problem as glides no longer had support). I reused the same felt pads and glued them to bottom of new glides with Goop. You need O ring compressor and expander for rollers. Drum belt was a little hard to thread at the belt tensioner and video was not real clear. If you use left hand around left side of motor to guide the belt and right hand around right side of motor to compress tensioner, it worked great.

This part fit perfectly. I pulled the old lint filter out and put the new one in with no problems. The part no longer contains a felt seal so if that's your problem just pull the old felt seal off as it doesn't seem to need one.

When the dryer stopped working, I checked the two switches to see if they were good. The start button checked out OK but the switch on the door read bad. Ordered the part with the part number and put on when it arrived. Just a matter of disconnecting and reconnecting three wires. Very simple

the idler lever is what finally fixed the problem but i ending up changing out the belt drum rollers and the felt glide pads before i fixed what it was. truthfully though its not a bad thing replacing all the moving parts. the hardest part about the rollers was the removal of the snap rings i had a pair of snap ring pliers that just didnt seem to work all that great and i ended up taking a screwdriver to pry them open which i dont suggest but its what i had available. other than that the videos are spot on. not hard at all.

No work was required. I just slid the filter in a hole.

Had to call the repair center 3 time & view the video several times because the drum support roller would not fit on the new shaft. Even ordered the parts twice (with refund on first) to ensure the correct parts. The call in center could not help me & I was left on my own. I had to force the roller onto the shaft which was very difficult, Once the hole had gone onto the shaft, it was fine, but I had to take it off to install the shaft then gently drive the roller onto the shaft. It does roll free once over the outer edge. Installing the belt was not easy either. The video did not have a good picture of how the belt runs & not drawing was available, maybe it could be included next time for others

I only had to watch your video! The absolute BEST instructions ever. Your videos have saved me already $480 in repair bills in just one month. First my washer needed a snubber ring, and you had that video and then the dryer parts. Thanks again for being there!

I don't have the model number right now, but you video was fantastic.