Maytag/Maytag_Thumb/58908.gif
See part 5 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Heating Element (Orange Dot)

★★★★★
★★★★★
7 Reviews
$48.61   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11757549
Manufacturer Part Number WPY503978
Manufactured by Whirlpool
Product Description

Heating Element (Orange Dot) Specifications

This orange dot heating element replaces those elements with an orange dot on the element flange. It carries 240 volts.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
No heat or not enough heat | Takes too long to dry
This part works with the following products:
Dryer.
This part works with the following products:
Amana, Maytag, Speed Queen, Crosley.
Part# WPY503978 replaces these:
AP6024199, 14218929, 503978, Y503978
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

4 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Ray
    January 30, 2018
    Where is the heating element located for Maytag dryer model number mdet236ayw? Is there a repair video for this specific model or similar model?
    For model number MDET236AYW
    Hi Ray, Thank you for your question. The element would be located in the heater duct assembly located in the back of the dryer. I hope this helps. Thank you and have a great day!

    3 people found this helpful.

    Was this helpful?
    Thank you for voting!
    RICK
    February 7, 2019
    No heat , i check all 3 thermo fuses they all show a short and the heating element ohms out at 9.8 ohms , which i think is good , could it still be a bad heating element?
    For model number PLea10AW
    Hello Rick, thank you for your question. Looking at your model information there are a few parts that you should take out and test to see which one is giving you the issue. The first parts to check in this case would be all of your thermostats and thermal fuses. You can test those parts with a multi meter and they should be reading 0 ohms to be working correctly. If those parts are fine, you should then go on to testing your heating element as well. You can also test that with a multi meter and it should be reading between 0 - 50 ohms. Something else you should also check would be your filter and ducts. Make sure there is absolutely no blockage that would restrict air flow in your appliance. I hope that helps. Good luck with your repair.

    3 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Gerard
    February 14, 2018
    How can i get the video on replacing heating element on Amana elect dryer?
    Hi Gerard, Thank you for the question. We do not have a video as of yet for this element but we do have a video for a similar element with the same basic steps. Hope this helps! https://www.youtube.com/watch?v=M9miM9kU3WU

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Anita
    January 29, 2019
    Does this part come with the thermostat & thermostat limit? Or do you purchase those separate?
    For model number SDE4606AYW
    Hello Anita, Thank you for the question. This is just the element. The Thermostats are sold separate. Hope this helps, good luck with this repair!

    Was this helpful?
    Thank you for voting!
      Customer Repair Stories
       Average Repair Rating: 3.6 / 5.0, 34 reviews. What's this?
      Sort by:
      Sorry, we couldn't find any existing installation instruction that matched.
      Timer won't advance for auto-sensing cycles. Low Heat.
      First I unplugged the dryer from the wall outlet. Then, removed the access panel in the lower front (held on by 2 screws near the floor). Then, I removed the black plastic air duct (held by 3 screws) in front of the blower. Then, with a Sharpie marker, next to each wire terminal lug, I labeled on the chassis the COLOR of each wire where it plugs on to a terminal lug (for proper wiring re-assembly later). Then, thru the lower front, I reached into the lower left rear of the dryer to remove the heating element assembly from its metal duct (held by 3 or 4 screws) - it slides down a bit, then it is easily removable. I layed the element on the floor in front of the dryer - all wiring still intact. Then, using the NEW HEATING ELEMENT and SENSORS ordered, I assembled them to match the original, re-using screws off of the old unit - and moving the wiring one-by-one from the original to the new assembly. I then installed the new heating element assembly into the duct at the lower rear of the dryer. I then replaced the 2 sensors on the front metal panel of blower housing, with new parts from my order, re-using the original wiring and screws. Then I re-installed the black plastic duct onto the front of the blower. Then, on the top of the dryer, I dissassembled the control panel from the rear, by removing 5 screws. I then found the resistor mounted on the back of the timer, and replaced it with the new one. Since the new resistor did not come with terminal lugs crimped on its wires, I had to cut the terminal lugs off of the original resistor and solder them onto the new resistor. I then reassembled the control panel. I then plugged the dryer back into the wall outlet and did a test run with no clothes. IT WORKED !! Then I reinstalled the lower front access panel and ran the dryer with wet clothes. IT WORKED !!
      107 of 141 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Dryer stopped heating up.
      Replaced heating element, which had a fuse and high limit thermostat attached to it. Remove 2 screws to pull the bottom cover plate on the dryer, remove 3 screws to pull the blower inlet shroud and then remove 2 screws to pull the heating element off the air inlet duct at the back of the dryer. Remove 2 screws each for the thermostat and fuse. Installed the new devices back onto the new heating element. Power leads to the element are long so you can pull the whole thing out very easily. Couldn't have been any easier to fix.
      • Anthony from Bethlehem, PA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Screw drivers, Socket set
      69 of 80 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      No heat. Bad heater element.
      Unplugged Dryer. Removed two bottom panel screws with nutdriver. Element in back left corner (under drum). Removed two screws holding element in place. Slide element down and pull out at a slight angle until entire element cleared and can be pulled out. Wires are long enough to reach out to the front of Dryer to make work easy. Had to remove two high temp thermostats and transfer to new element. Moved wires that were left and transfered over to new element. Reinstalled element and front cover. Plugged in Dryer and turned on. HEAT AGAIN. EASY!! With a little coaching I could have had my 8 year old do the repair. Honestly, it was that easy. Don't be intimidated and pay the repair man $350 to fix it for you. At least not on my model of Dryer! Hope this helps someone!!! To be honest, it probably took me longer to post this description than it did to make the repair.
      • Timothy from Kunkletown, PA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        Less than 15 mins
      • Tools:
        Nutdriver
      • Parts Used:
        WPY503978
      47 of 49 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      dryer took several cycles to dry
      I took the front bottom cover off. In the lower left corner in the back of the dryer was the element. I removed the two screws that held it in place. The wires were long enough to reach the front of the dryer with the element for eas of switching. I pulled the element out to the front of the dryer and switched wires. Slid new element in place which looks trickey but it sits right were you need it too so you can get screws in. I put cover back on ran a cycle with no cloths to burn off the element and as good as new.
      • john from east baldwin, ME
      • Difficulty Level:
        Easy
      • Total Repair Time:
        Less than 15 mins
      • Tools:
        Nutdriver, Socket set
      • Parts Used:
        WPY503978
      25 of 27 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Dryer would not heat
      This dryer required complete take apart to get to heating element, including removal of drum. Multimeter indicated thermal fuse blown. I replaced it and it blew again. I replaced fuse(again), heating element, limit thermostat, and cycling thermostat to eliminate all potential causes. Dryer works like new. Cycling thermostat had been bad for years, but I never knew it, just had to run dryer two cycles all the time.
      19 of 24 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Multiple long cycles to dry clothes
      Remove 2 screws on the front panel at the bottom of the dryer & remove front panel. Remove the black plastic "duct" from blower to lint filter by removing 3 screws. Heating element is on the back wall of the dryer in the lower left corner. 2 screws hold the heating element to the dryer wall. Remove these 2 screws. Might be a little tight to get back there. Try to be more patient than me. :) The wires on the heating element are plenty long enough to bring to the front & outside of the dryer. Remove screws holding thermostat & fuse to heating element. I wasn't sure if I needed a new thermostat or not, but it wasn't expensive so I went ahead & decided to put a new thermostat on the new heating element. I re-used the fuse from the old element, but they're not expensive either. Just notice how rthe thermostat and fuse are oriented on the old element & put them on the new element in the same orientation. I had to use pliers to get the wires off the old element's terminals. They were a little tricky to get off, but my dryer is over 10 years old. They've been on there a while. Just move 1 wire from old element to new element at a time. That way you don't have as much of a chance hooking up the wires wrong. Put new element in & everything back together. I vacuumed out the lint in the bottom of the dryer. I ran the dryer for over 30 minutes with no clothes in it to break the new heating element in. You're good to go! You CAN do this yourself. It's not a hard repair to do. Don't buy a new dryer or pay an appliance repair guy! Thanks to PartSelect for quick delivery & posting these instructions from other people!!
      • Chris from Hampton, GA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Pliers, Socket set
      • Parts Used:
        WPY503978, WPW10116735
      11 of 13 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      No Heat to dryer
      Went so easy. Removed two screws holding the front cover on. Reached into the back and removed the two screws holding the heating element in. Removed the element(the wires are long enough to pull all the way to the front of the dryer). Took one wire at a time and transposed it to the new element. Then re-installed the element. It maybe took 15 minutes.
      • Brian from Newport News, VA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Pliers
      • Parts Used:
        WPY503978
      10 of 13 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      no heat
      I first removed the two front screws on the front cover located on the lower half of the dryer using a flash light looking on the left side all the way to the back you will see two hex screws removing them will now let you wiggle the heating element back & fourth while pulling down it will come out in just a few seconds - then with your digital camera take a picture of the still wired heating element as to a clear reference for wiring the new element - first Aline the new element in the same direction as the old element and transfer them one by one check camera for assurance that you have done it correctly and re-reinstall in the reverse order

      also I would recommend taking off that black plastic blower chute and cleaning it assuringly the best performance of air flow
      • Janet from Portland, OR
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Socket set
      • Parts Used:
        WPY503978
      7 of 8 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Dryer would not heat
      First I turned off the circuit breaker, then removed the two screws that hold the front lower panel in place. Once open I removed the 2 screws that held the element in place. (Far back left side) I then pulled the element out leaving all wires connected. Wires are long enough to extend out to the floor in front of the dryer. I simply exchanged the wires one at a time to the new element so no mistakes could be made. Reinstall, reset the breaker, and Instant HEAT. Repaired for under $40.00
      • James P from Agawam, MA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Screw drivers
      • Parts Used:
        WPY503978, WPW10116735
      6 of 7 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      No Heat
      Ordered the new heater element on Saturday and got it on Tuesday. I have ordered from PartSelect before and the service has always been fast and accurate.

      The first thing I did was to unplug the dryer and then removed the bottom front pannel by removing two hex screws, one on each side near the bottom of the dryer. Use a flashlight if you need to see better. I then used my shopvac to vacuum all the lint that had gathered over the years, including the old heater element located on the left side towards the back bottom part of the dryer. Located the two hex screws and unscrewed them to remove the heater element. Pull out a bit from the bottom and then down. Pull towards you and remove the wiring from the old heater element making sure where the wiring and parts to be reused go so they could be transferred to the new heater element. Re-attach the heater element with two hex screws. Replace front cover and plug in the power cord and start drying clothes.
      • Rogelio from Loxahatchee, FL
      • Difficulty Level:
        Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver, Pliers
      • Parts Used:
        WPY503978
      4 of 4 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      7 Reviews
      5.0
      Filter By Rating:
      • 5 Stars
        7
      • 4 Stars
        0
      • 3 Stars
        0
      • 2 Stars
        0
      • 1 Star
        0
        Sort by:
        Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
          Model Cross Reference
          This part works with the following models:
          PartSelect Number: PS11757549
          Manufacturer Part Number: WPY503978
          Brand
          Model Number
          Description
          Admiral
          ADE7005AKW
          Dryer - Residential
          Admiral
          ADE7005AYW
          Dryer - Residential
          Amana
          ALE120RAW
          Dryer - Electric
          Amana
          ALE230RAW
          Dryer - Residential
          Amana
          ALE331RAC
          Dryer - Residential
          Amana
          ALE331RAW
          Dryer - Residential
          Amana
          ALE331RCW
          Dryer - Residential
          Amana
          ALE443RAC
          Dryer - Residential
          Amana
          ALE443RAW
          Dryer - Residential
          Amana
          ALE565SAC
          Dryer - Electric
          Amana
          ALE565SAW
          Dryer - Electric
          Amana
          ALE643RAC
          Dryer - Electric
          Amana
          ALE643RAW
          Dryer - Electric
          Amana
          ALE643RBC
          Dryer - Residential
          Amana
          ALE643RBW
          Dryer - Residential
          Amana
          ALE665SAC
          Dryer - Electric
          Amana
          ALE665SAW
          Dryer - Electric
          Amana
          ALE866SAC
          Dryer - Electric
          Amana
          ALE866SAW
          Dryer - Electric
          Amana
          ALE866SBC
          Dryer - Residential
          Amana
          ALE866SBW
          Dryer - Residential
          Amana
          ALE868QAW
          Dryer - Electric
          Amana
          ALE956EAC
          Dryer - Electric
          Amana
          ALE956EAW
          Dryer - Electric
          Crosley
          CDE6505W
          Dryer - Residential
          Crosley
          CDE9500AZW
          Dryer - Residential
          Crosley
          CDE9500W
          Dryer - Residential
          Crosley
          CDE9505AZW
          Dryer - Residential
          Crosley
          CDE9505W
          Dryer - Residential
          Magic Chef
          CYE3005AKW
          Dryer - Residential

          Get in touch, we're here to help!

          Open until 1am EST

          Contact Customer Service