KUDS24SEWH1 KitchenAid Dishwasher - Instructions

Removed old phillips head screws /w washers from spray arm kit and mounting bracket. (You'll need to keep one screw/washer set.) Attached new mounting bracket and screwed securely. Attached spray arm with new screw/washer and I was good to go. Piece of cake!

I originally ordered the wrong version of the rollers, but the repair department walked me through the proper procedure.

We only needed to clamp on the holder attachment to the rack and secure it with a pair of pliers. Then snap on the wheels and viola!

End of happy story.

replaced spray arm, but this did not resolve the problem. The troubleshooting guid (inside kick panel) indicated the check valve may be stuck. We had quite a bit of lime build up, so I suspected the loose deposits may be stuck. I removed all of the deposits, disassembled the lower unit.
Removed lower spray arm, removed spry tube. The tube is two pieces. first the upper portion must be removed (two screws-place towel on base of tub to preven screws from falling into the chopper area), and then the lower portion simply rotates clockwise 1/8 of a turn. The attachment for lower spray arm has a small plastic bearing, careful not to drop it.
The dishwaser then had to be pulled out and turned on the side. I removed the entire lower unit by removing the white tabs (3). Careful, because the unit is now free to drop into the tub. Next I removed the pump. This is tricky as you have to remove the aluminimum bracket to get to the mountin bolt. The bolt turns out easily w/socket and extension. The pump motor is then rotated counter clockwise, and pulled from the pump. Takes a little force as the gasket makes for a tight fit.
I then removed the choper / pump unit from the basin. The build up behind the chopper screen was extensive, so I had to remove the screen and then the chopper cover. After cleaning, the check valve was unplugged and I reassembled the unit.

Dishwasher works great now.

Just removed the old seal and followed the instructions that came with the new one. Since the old one didn't have any adhesive on it ,I didn't use the adhesice on the new one. Problem solved!

Followed the other repair instructions on this site to replace the fuse assembly. I could not have figured this out without the drawings and user descriptions. Thanks!

Did not have to do any repair, the parts for the dishwasher come with all the necessary parts and no tools were necessary. the wheels were snapped into place for the lower rack and the upper rack should needed to be place in the sliders. The Middle arm holder is not necessary as it comes standard.

I followed the video available on partselect.com and was easily able to follow step by step the process of removing and reinstalling a new Drain and Wash Impeller and Check Ball.

Removed the old mount from the upper rack. Removed the broken stem from the old mount that was attached to the arm. Attached the new mount to the spray arm. Attached the mount and arm to the rack.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

I looked up the part on the Internet and checked locally. The part had to be ordered locallybso I placed my order on line. The part came quickly and the instructions were fairly clear. The parts just clipped together which made it vey easy to so and it is nicer than the rack we had before.

Simply followed the instructions that were provided with the part.
Locking the inside vented piece to the outside assembly was difficult because it is located deep along the side of the dishwater (leverage) and I was not sure how much pressure to apply to the part for fear of breaking it. But it did snap into place after several attempts.

Removed 2 screws that held the old mount and washer arm in place, new mount was very easy to install, it snapped in, only one screw needed, remounted the washer arm and the job was done. I was really impressed with the ease of ordering and how quick it got here (3 days), also the scematics you have online are very helpful. I printed them out since I don't have the owners manual any longer, they're very helpful in matching up and ordering the right part which saves a lot of time, also I like the way you can just search by model number and appliance name to find the right parts, makes the entire process really easy. I know I will continue to shop here when the need arises. It really cuts down on expensive repair costs.

I had replaced the control board a month or two earlier. Then smelled plastic burning. I noticed the Sta-con connecters in the molex plug had burned - that's what took out the control board. The fuse assembly came with new connectors - so you know this is a known problem with the machine. If you're handy you can buy the thermal fuse from Newark for $0.88 and replace it by soldering - but you need to replace the sta-cons. They corrode and the bad connection causes the heat making the thermal trip.

Hey parts select, I'm Julia's husband and the repair was a simple remove and replace. Only one screw to hold the manifold together and the mounting hardware that we had to order separately was a snap in piece which was different form the original but went in just fine. You saved me from having to buy a new dishwasher which Julia was more than happy to go shopping for!! Thanks!!

Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much