Models > KUDI24SEBL1 > Instructions

KUDI24SEBL1 KitchenAid Dishwasher - Instructions

All Instructions for the KUDI24SEBL1
631 - 645 of 673
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher was probably loaded wrong by kids. Broke upper spray arm and upper bracket.
Looked at your excellent blow-up of part assembly of my model and ordered parts. Upper bracket had been redesigned from original. Quick replacement repair, no leaks, all is well.
Parts Used:
Screw Upper Spray Arm Mount
  • Alan from Stansbury Park, UT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
the sprayer arm was shot
unscrewed the old one an attached the new one, it was a very easy fix
Parts Used:
Middle Spray Arm Kit
  • Deb from Sherburn, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Rubber water hose for upper arm was rotting from age ,and upper arm was corroded from hard water and would not spray properly
Watched the video recommended with the kit.Absolutely self explanatory, and very clear. All parts needed were in the kit, and complete repair took less than 10 minutes.Ordered the kit online on tues noon. Kit was delivered by 1:00 pm on Wed. Fantastic service !Just found my new parts supplier !
Parts Used:
Middle Spray Arm Kit
  • Richard R. from Plainfield, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken spray arm mount & tube holder
followed partselect video online
Parts Used:
Upper Spray Arm Mount Middle Wash Arm Tube Holder
  • phyllis from ridgeway, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
After cycle was complete dishes were still dirty
followed the basic instructions / diagram supplied, however the impeller was fused to the shaft. Used high speed cutter to remove old impeller and sandpaper to clean up shaft.
Parts Used:
Drain and Wash Impeller Kit
  • DOUGLAS from SNOVER, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Bought house, dishwasher wasn't working properly
The DW that came with the house I bought wasn't working properly. I reviewed the owner's manual that I downloaded online and determined that it was missing the tube that connected the upper sprayer to water supply. I watched the Youtube video that was embedded on part order page. It took me about 5 minutes to install new sprayer arm assembly (and it took only 2 days to receive the part with no special shipping. Highly pleased.
Parts Used:
Middle Spray Arm Kit
  • Gary from Blanco, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Sprayer was broken.
Took the old one off and replaced with the new one.
Parts Used:
Middle Spray Arm Kit
  • Dean from Derby, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Replace upper spray arm mount
The broken mount was removed with a screwdriver. The replacement was a modified design and had no screw clamp-it just snapped into place. The location on the rack was clear because only one position on the upper rack had the correct spacing between the rack wires. However, once the spray arm was attached with a screwdriver, it was at an odd angle and would not rotate as it ran into the rack. However, removing the mount (required a small screwdriver to press the snaps and release) and reversing it provided the correct angle for the spray arm. The mount needs to project at an angle perpendicular to the UNDERSIDE of the upper rack so that the spray arm rotates parallel to the underside of the rack, not level.
Parts Used:
Upper Spray Arm Mount
  • Andrew from Davis, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Mount was broken
Replaced old broken one with new one.
Parts Used:
Upper Spray Arm Mount
  • Warren from Charlottesville, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door latch broken on Kitchenaid Dishwasher
Removed the front panels and then wedged a screwdriver to get the door latch open. Removed the 4 star screws across the top inside to remove the top console. Unlatched the grey ribbon cable, then removed the 3 screws holding the electronics panel in place. Replaced the plastic handle, then aligned the metal bar in place before reversing the direction to put the thing back together. The hardest part of the job was wedging the screwdriver up in the opening to get the door to open in the first place.
Parts Used:
Door Handle
  • Scott from Norcross, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
the upper spray are attached to bottom of top rack
looked up the appliance, and then pulled up a skimatic. Ordered the required replacement parts. 3 days later they arrived. I watched the short u-tube video and fixed it myself!
Parts Used:
Screw Upper Spray Arm Mount Upper Spray Arm Mount Middle Spray Arm Kit
  • Lee from boca raton, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Need to replace original middle spray arm which was cracked and split
I reviewed the video provided for the replacement part on the PartSelect website and then did the job, lickity-split.
Parts Used:
Middle Spray Arm Kit
  • Steve from Essex Junction, VT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
leaking badly & not cleaning dishes
You need a properly sized hex (Allen) wrench to get the screws out. Basically simple: remover bottom roller tray, unscrew large plastic holding bolt, remove lower spray arm, unscrew bolts (be sure the wrench is sized right or you might strip the heads), and replace gasket; then reverse procedure. Chances are if the gasket was bad, it will be very obvious (out of circular slot and stretched).
Parts Used:
Pump Outlet Seal
  • Eric from Ritzville, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Rotted water feeder tube and broken dispenser.
Middle spray arm kit - WATCH the video!!! After watching the video, I knew I could do the repair. It took me about 15 min. The detergent dispenser - I know this will require more time. I am a "visual" person and I could not find a video for dispenser repair...I could be overlooking it.
Parts Used:
Detergent Dispenser Middle Spray Arm Kit
  • Donna from Dover, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Rubber part of old arm was bent.
I watched the video on the partselect web site and just followed the procedure on the video and it went perfect.
Parts Used:
Middle Spray Arm Kit
  • Anthony from Mount Vernon, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KUDI24SEBL1
631 - 645 of 673
Back to Top