KUDE60FXBL0 KitchenAid Dishwasher - Instructions

The repair was easy. You will need to make sure any screws securing the dishwasher are removed at the top front of the dishwasher under the counter and above the top of the dishwasher. Then pull the dishwasher out exposing roughly 18" of each side of the dishwasher then use a socket to remove the screws holding the tracks in place, 4 in total on each side. Then install new tracks and slide dishwasher back into place and secure.

1. Disconnect power at the breaker, 2. remove two wood screws fastening the dishwasher to the cabinet and slide the unit out approximately 2 inches. 3. Remove old latch strike and replace with redesigned strike. 4. Slide unit in and reattached to cabinet. 5. Remove 11 screws holding inner panel of door assembly and one screw holding user interface unit to door. 6. Disconnect snap cable to latch assembly and replace the latch unit. 7. Reassemble.

Popped out old wheel housing. Popped in replacement with a little help from a flathead screwdriver. Easy.

Simply snap the old one off and snap the new one on. Simple as that less than 15 seconds.

Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.

Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.

Delivered in 1 day. Fantastic. Highly recommend

Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done

Easy...easy....I first watched YouTube videos on how to fix our problem. We replaced both tracks and also the rack adjuster on both sides of the rack. The entire repair took about an hour and most of that time was spent finding the tools at our house!! I ordered the parts on a Sunday evening and they were at our house on Tuesday!!! Will use this sight again if repairs are needed.

It was very easy to pry off the old wheel assemblies with a screwdriver and pop the new ones in place. Although the part is called "wheel" it is actually the plastic piece containing two wheels. I thought it was a little confusing to just call it "wheel" as each piece has two wheels. It was an easy repair.

Followed a video, pretty straightforward. Be sure to clean all the area. My husband used cotton swabs to clean all the gunk.

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

The only appliance that wasn't SS was my $900 dishwasher that was tiled-in when my kitchen floors were done...I can only replace it by removing the granite counter. I ordered the SS front and handle to update the look of the 4 year old DW and it was a really good idea. * screws later and it was done. The 'repair' took 15-20 minutes and the results are amazing. BTW...the parts took less than 2 business days to arrive...

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

New latch assembly improved door closure. However, door latch did not solve problem. There appears to be another problem.

I replaced both upper rack tracks because the spot welds on one of the factory tracks failed after 18 months. The welds just rusted away and let go. The other track appeared to be close to failure so I replaced both of them. This repair is actually quite easy, but in order to change the tracks, you must pull the appliance out at least a little more than halfway in order to reach the screws that hold the tracks in place. There are four such screws on each side -- they are fastened through the exterior face of the tub. Here is the process:
Use a 1/4" nut driver to remove the bottom front (kick) plate from the appliance. There are two screws, one at each end. There should also be two screws fastening the dishwasher to the countertop. You'll need to open the dishwasher door to see these and remove them. At the bottom of the dishwasher again, you might need to screw the front (2) leveling feet in to lower the dishwasher and provide clearance. Once done, just (gently, slowly) pull the appliance out of the cabinet. Check to make sure your power wiring, drain hose, and water supply hose are all long enough to do this. If necessary, disconnect any of these that are too short. if your power wiring is short, as mine was, you'll need to disconnect the circuit breaker, then remove the junction box at the lower front right side of the dishwasher, then disconnect the power and ground wires.
Once out of the cabinet, use a 5/16" nut driver to remove the four screws holding each rack slide in place and remove the track. The rubber mounts will come out with the track (new tracks include new rubber mounts). Clean any residue from the track mounting area inside the tub before installing the new track. This whole replacement process should take a total of 3-4 minutes per side.
To finish up, just reverse the process. When sliding the dishwasher back into place, make sure the fiberglass insulation stays in place completely around the outside of the tub.
Because the tile on my kitchen floor does not continue under the dishwasher (tile was installed after the cabinets), it was absolutely necessary to turn in the leveling feet to get the appliance out. Since this also makes it very difficult to get a wrench around the plastic feet, I used a very small socket (3/16"?) on the top of the leveling feet stems. This makes it really easy to turn the feet.
I the appliance designers had engineered things better by fastening the tracks from inside the tub, this would be a 5-minute job. But it's still not bad at all.

Removed old gasket, cleaned track and replaced gasket-also quit using Cascade pellets and went back to using Cascade powder with a numerical "rating" of 6. The pellets of even 10 caused the washer to leak, obviously too much foam would not float the float to actuate the pump.