KSRG25FKSS04 KitchenAid Refrigerator - Instructions

Unplug refridge, shut off water supply, remove backing. Remove two screws holding in valve, pull out valve and remove water lines. Have towel to wipe up very little water that leaks out. Unplug electric sources, remove old valve. Take new valve , plug in electric sources, push in water supply until they bottom out, attach bracket to back of refridge. Replace backing, turn on water supply, plug in and bleed lines.

removed the three screw holding the broken unit - pulled off the old module.

Before I could install new module I had to loosen some fasteners on ice maker so I could turn shaft to align with new module.

Then push on new unit and three screws. Had tumbling ice in about an hour. My wife thinks I'm a hero. (I am)

Removed six screws from cover in the back of the freezer. Removed old fan . Removed power wires from old motor. Unclipped old motor from the mounting bracket. Replaced old motor and reversed the rest of the parts. Done

Replaced upper cam piece on bottom hinge and also replaced pivot thimble on upper hinge.
No problems, except pivot thimble glued in place. Had to cut up and pull out with pliers. Everything works like new now.

At their site was ordering each piece by # and cost and it was adding up to be costly. Went to partselect and was doing the same and up pops the ice door kit. Was a little wary because my original had a heater tape to it. Got the kit and installed not a problem at all. 100% satisfied would recommend to anyone.

It was pretty easy to install. The most difficult part was trying to get my hands into the small area to work. I had to use both hands, one to push the release in and the other to pull the tube out. Once I did that, inserting the tube was easy and everything worked perfectly.

I removed the back panel off the fridge and removed the old start relay device by simply unplugging it from the compressor. I had to detatch two wires and a capacitor from the device. The old start relay was definitely bad and you could tell by shaking it. Plugged in the new start relay device, reattached the wires and capacitor and was done. Fridge is perfect now! Very simple!

I discovered that the freezer was not defrosting automatically and the condenser coil was freezing up blocking the flow of cold air to the refrigerator side. I first replaced the thermostat thinking that it would be an easy fix but needless to say it didn't work. My indicator that it was not a successful repair was the continuing blinking of the filter change light on the control panel. Ultimately I had to replace the control board assembly to solve the issue.

First I removed the icemaker from the freezer by removing two horizontal screws holding it to the side wall, and one vertical screw holding the front to a bracket coming off the side wall. Then I used a flat screwdriver to unlock the electrical plug. (After doing this, I realized that this wasn't necessary at all, and this part could have been changed just as easily without removing the icemaker.) On the front, there is a white cover with Ice Maker Plus. Use a flat screwdriver to unlock the tangs and remove the cover. There are three screws in the corners that once removed, will allow the motor assy. to be gently pulled straight out. On the back of the part, you will see many gold lands that the timer touches. I don't think there was anything wrong with my motor. I had two spots where the gold plating was worn off, so I suspect it was not making contact, and the whole process would stop. Slide the new part in place making sure the teeth on the gears line up (not a big deal), and secure with the screws. Install cover and you're done. Mine has been making ice like it was brand new.

Turned the lock knob on the filter and removed. put
lock knob on new filter and installed.

Very user friendly website, would highly recommend to anyone.

First off, if you have the stainless steel panel inserts on your refrigerator you'll need to remove those to do this repair. I kept looking for the access holes on the underside of the dispenser panel that you're supposed to insert a screwdriver into to pry it off. It wasn't until I removed the freezer door handle, slid the lower stainless panel insert out, and removed the rail just beneath the dispenser that I could see and access these holes. I also removed the upper stainless panel and rail just above the dispenser to allow enough movement get the dispenser cover off and out. The rest of the repair is pretty straightforward. The old ice door was beaten up and not closing completely, this was letting warm air into the freezer which was melting and re-freezing. This kit fixed the problem.

The refrigerator would not come back on after the defrost cycle unless I smacked the housing around the controls. Since it would come back on after stricking the housing I knew it must be a sticking relay. I used the exploded drawings from Parts Select to determine how to disassemble the housing. Once the part arrived I swapped it out in about 10-14 minutes. The drawings made the job simple. Thanks Parts Select!!! -neal

Removed 2 screws holding housing to frame. Pulled housing out 10 inches. Removed water lines. Attached water lines to new housing. Pushed back into place. Secured to frame with 2 screws. Put in new filter. DONE!

Removed the old filter (it screws out) an put the new one in!

I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.

Thank you
Curtis Hall