Door would not close on its own. Stopped 1" short of closing unless pushed in all the way
This was easy. Removed the plastic cover at the top hinge. Removed the 3 screws at the top hinge. Lifted the door off of the bottom hinge and laid it on it's side. The part that was worn out is the "natural door closer". It looks like this part will need to be replaced every few years, it is made of plastic and was ground down to nubs. Remove the screws holding it down and replace it with the new one. Lubed it up with some WD40 to get rid of squeaks. I also replaced the lower hinge pin, but I don't think that was necessary.
At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.
Switch was not working after a repairman had fixed something else
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Obtained the part from part select in record time. Exact part arrived next day and changed out the faulty part within an hour. great service and have already booked-marked the website should future appliance parts be needed. Fair price too!
I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.
Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place
Most of the time was sent to removing and replacing door shelves. Pry off upper hinge cover. Easy, it's only plastic. Remove 3 fastener from top hinge and remove hinge. Lift door off lower hinge. Lay door down on table let handle hang over edge. Remove door closer attach fastener. Remove and replace door closer. Pry lower hinge up and out. Tap new lower hing pin into place. Replace door, upper hinge and hinge cover. Had to replace Door Closer and Hing Pin together; both were worn and needed replacing.
Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.
Repair requires the removal of the bottom hinges on the doors. No problem for the refrigerator side, but the freezer side has wiring in the freezer door for the water/ice dispenser, so have some wood blocks handy to prop it up. Biggest challenge is that in the center of the kickplate there is a mounting screw (Torx head) that is behind the kickplate and runs vertically. I removed the old kickplate without removing this screw, just broke the kickplate off. The screw is very difficult to access with any tool. Removal wasn't too terrible because the old kickplate was gone; but insertion with the new kickplate in place was a challenge. I used a Torx socket, but because there isn't enough clearance for the ratchet, I held the socket into place by wedging a large flat blade screwdriver between the bottom of the socket and the floor. I was just able to get my index finger under the new kickplate to slowly turn the socket to fasten the screw. Unfortunately I didn't feel as though I could skip the screw - without it the kickplate sags in the center.
Took out lower shelf. Unscrewed screws holding two broken shelf supports and removed broken supports. Replaced with new supports and screwed in the screws. Nothing to it.