Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JES9800AAB > Instructions

JES9800AAB Jenn-Air Range - Instructions

All installation instructions for JES9800AAB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JES9800AAB
271-285 of 390
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Filter was old and discolored.

  • Customer: Robert from Warroad, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The new replacement grease filter came without damage and it was a simple task of removing the old and setting the new in it's place. No tools were required.

bake element burned out

  • Customer: Gerald from Coventry, RI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled stove out from counter. Unplugged power cord. Took out the two racks. Unscrewed two screws with a Phillips head screwdriver. Pulled out element and disconnected wires and reinstalled new element in reverse order. Plugged back in and replaced stove back in counter and put racks back in. Took a Pizza out of freezer and cooked at 400 for twenty minutes and drank a ginger ale. Install took less than 20 minutes.

Baking Element burned out

  • Customer: Edward from Cibolo, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
unplugged the oven; screwed out the element from the inside and replaced it with the new one.

Inner glass oven cracked

  • Customer: Christine from Eureka, NV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The feedback from other customers was excellent. It does come apart in layers, and it helped me to number each layer with a sticky note as I dismantled it. I also kept the screws for each layer right next to the layer, so that I knew how many screws each layer used. The only thing I can add is that the tabs to remove the innermost glass from the frame are on one of the shorter sides of the rectangular frame. The tabs are part of the frame, and when you bend them outward the side of the frame detaches and you can replace the glass easily. In addition to the #1 Philips screwdriver, all I needed was a pair of pliers to bend the tabs.

Oven baking element burned out & broken

  • Customer: Paul from Middlebury, VT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Screws had to be removed where the two ends of the old element are attached to the back of the oven. The wires can then be pulled out 2 or 3 inches into the oven and the connecters which are attached to the wires can be pulled off from the ends of the old element using pliers. Push the connecters onto the ends of the new element and push the wires through the back of the oven and replace the screws. I found it easier to remove the oven door for easier access.

Needed to install new element

  • Customer: Frank from Langhorne, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Assembly took a little while, but that had to do with the stove, not with the element you provided. Turned it on and it looks like it's working well. (It's been so hot I haven't cooked since putting the new one in, so we'll see how that goes. But, when tested, it heated right up).

Needed to replace a burner switch for an inspection

  • Customer: Dan from Greenville, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the cover plate for the burner switches and verified the wiring on the other switches. I had removed the bad switch a few years ago and I needed to make sure that the wiring was correct. I did not keep the original screws that hold the switch in place, because I destroyed them when I first removed the old switch. The were corroded from years of cleaning solution. I made new screws from longer wall socket screws by shortening them with a hacksaw. The entire process took about 30 minutes to do, and the results were good. The new switch is smoother than the others, but functions exactly the same.

switch on top of stove

  • Customer: James from Beaufort, SC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
James is an electrician so he istalled the part himself

Oven would not heat

  • Customer: Claude from Lakewood, OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)

The lower (baking) element burned out.

  • Customer: Timothy from Helena, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I'm the world's worst handy man, but after watching the repair video on PartSelect I determined I might could do this repair. I ordered the part and replaced the element in less than 10 minutes! I also saved $160.00 by doing it myself!

Oven would not program and would shut down

  • Customer: Sreve from Deland, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The "PartsSelect" General discription of the parts funtion helped me to confirm my suspitions that there was some form of temperature registering problem. I whatched the short video they provided on how to change the part out, even though, in this case, it's pretty self explanitory.The part was in my hands a day erlier than promised and in reality, much earlier than I had anticipated from the beginng. It took me all total, 20 minutes to exchange the part out and have the oven in operation again.

F1 Fault Code - Replace the Temperature Sensor

  • Customer: Dennis from Tampa, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.

Rear butner no longer worked after liquid was spilled on range.

  • Customer: Paul from Bothell, WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just followed the instructions on this site... :) Unscrewed the front, removed old unit taking care of which wires went where, put in new unit. Voila.

Burner was very hot regardless of setting

  • Customer: David from Woodland Park, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Your site helped me determine the problem. You included a video of how to do the repair. The replacement of the parts went just as expected. The parts came quickly and were the correct parts. I could not have asked for a better experience. (I replaced two switches because the knob was loose on the othe one).. Thanks.

Bottom Range Bake Element.

  • Customer: Debra from Marshfield, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I am a 60 year old women and I was so amazed that this was so easy, Except for whom ever put in striped screw before, got that out with a pliers. Thanks for your video online. Beautiful.
All Instructions for the JES9800AAB
271-285 of 390